manualshive.com logo in svg

Miele F 1412 Vi, Инструкции по эксплуатации и монтажу

Поделиться
Скачать
Miele F 1412 Vi Скачать руководство пользователя страница 88

Adjusting the interior fittings

88

Removing the shelf above the
ice maker

Use both hands to grip the front of
the shelf from below and press it on
both sides until you feel resistance

.

When pulling out and inserting the
shelf, make sure that the side walls
are not damaged.

Carefully pull the shelf out to the
front.

To insert it, slide the shelf slowly onto
the guide on both sides and then
slide it all the way in.

Removing the freezer baskets

Open the appliance door as wide as
possible.

The opening angle of the appliance
door must not be limited to 90° be-
cause otherwise the freezer baskets
cannot be removed.

Pull the freezer basket out as far as it
will go.

Raise the snap fastening 

 on both

sides, unclip, and carefully lift the
basket out.

To replace it, pull the telescopic run-
ners 

 out as far as they will go.

Place the freezer basket back in
again.

Slide the basket all the way back in
again until it engages in the snap fas-
tening.

Содержание F 1412 Vi





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды