Miele F 1412 Vi Скачать руководство пользователя страница 31

Страница: 31 / 124

Installation

*INSTALLATION*



Risk of injury and damage due to

tipping refrigeration appliance.
If the anti-tip brackets are fixed too
high up, they cannot be used to se-
cure the refrigeration appliance.
The distance between the
anti-tip brackets and the refrigeration
appliance must not exceed
5/16" (8 mm).



Make sure that the gap between the
refrigeration appliance’s rear wall and
the building-in niche does not exceed
2" (51 mm).



Place a wooden wedge behind the
anti-tip brackets



if necessary.



While holding the anti-tip brackets in
place, mark the necessary drill holes
on the rear wall of the installation
niche.

Fixing screws for different uses and
types of material are supplied in the
accompanying pack.

Securing to a concrete wall

Securing to a wooden wall

Содержание F 1412 Vi





























































































































Результаты поиска

Содержание F 1412 Vi

Отзывы:

Бренды по названию

Популярные бренды

Miele F 1412 Vi, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание F 1412 Vi

Отзывы:

Бренды по названию

Популярные бренды