Miele F 1412 Vi Скачать руководство пользователя страница 81

Страница: 81 / 124

Selecting additional settings

The

Water Filter Display

has been

switched off.

Resetting the

Water Filter Display



After you have replaced or cleaned the
water filter, you must reset the

Water Fil-

ter Display

so that it can be displayed

again after 6 months.

If you do not reset the display, it ap-
pears again and again.



In Settings mode



, use the



and



sensor controls to select the

Water

Filter Display

and select

to confirm

your selection.



Use the



and



sensor controls to

select

Reset

and select

to confirm

your selection.

The

Replace the water filter

message dis-

appears from the display.

The

Water Filter Display

has been acti-

vated for the next time the water filter
requires cleaning or replacing.

Содержание F 1412 Vi





























































































































Результаты поиска

Содержание F 1412 Vi

Отзывы:

Бренды по названию

Популярные бренды

Miele F 1412 Vi, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание F 1412 Vi

Отзывы:

Бренды по названию

Популярные бренды