background image

GR8-1200 OEM

Midtronics Inc.     7000 Monroe Street     Willowbrook, IL 60527

www.midtronics.com

28

Chapter 6: System Test

Use the UP or DOWN ARROW key to scroll to each screen. To 
return to the Main Menu, press the END soft key. If you are 
performing a System Test, press the NEXT key to continue with 
the Starter System Test.

Battery 

decision

Measured 

voltage

Selected 

rating

Measured 

rating 

Starter Test

1.  When prompted, start the vehicle’s engine.

2.  The GR8 will display 1 of 8 starter decisions with the com-

plete results in a series of screens similar to those shown 
on the right. Use the UP or DOWN ARROW keys to scroll to 
each screen. 

To print, press the

 

PRINT soft key. To continue testing, 

press the NEXT soft key.

 

NOTE

:

 In some cases, the GR8 may not detect the 

vehicle’s starting profi le and will display the op-
tions STARTED and NO START. Select STARTED, to 
continue with an alternator test. Select NO START 
to end the test process.

Starter System Test Results

Screen 1 of 2

Average cranking 

voltage

Average cranking 

current if amp 

clamp is used

Cranking time 

in seconds

Screen 2 of 2

Y axis = System 

performance: 

cranking voltage

X axis = Time

Table 12: Starter System Decisions and Recommendations

Decision

Action Recommended

CRANKING  

NORMAL

The starter voltage is normal and the 

battery is fully charged.

LOW VOLTAGE The starter voltage is low and the battery is 

fully charged.

CHARGE 

BATTERY

The starter voltage is low and the battery 

is discharged. Fully charge the battery and 

repeat the starter system test.

REPLACE 

BATTERY

(If the battery test result was (REPLACE or 

BAD CELL.) The battery must be replaced 

before testing the starter. 

NO START

The engine didn’t start and the test was 

aborted.

CRANKING 

SKIPPED

The GR8 didn’t detect the vehicle’s starting 

pro

fi

 le and skipped the Starter Test.

Содержание GR8-1200 OEM























































Отзывы: