15
Tape the Rear Wall Template onto the wall matching the centerline
and touching the bottom cabinet frame.
to Cooktop
C
3/8" TO EDGE
%#76+10Ä+(
':*#756#
ਸ਼+5
215+6+10'
&1765+&'
4'%1//'0
&'&&+/'0
5+10)4'#
5'Ä.#&'0#+
49+..
&
+5%*#4)'+
061*175'
5647%674
'
/+0+/7
/9+&6*
4'37+4'&
4'#49#..6'/2.#6'
NOTE: IT IS
VERY IMP
ORTANT T
O
READ AND
FOLLO
W THE DIR
ECTIONS
IN THE IN
STALLA
TION INST
RUCTIONS
BEFORE
PROCEED
ING WITH
THIS
REAR WALL
TEMPLATE
.
This Rear W
all Template
serves to po
sition the bo
ttom
mounting pla
te and to loca
te the horizo
ntal exhaust
outlet.
1. Use a leve
l to check t
hat the temp
late is position
ed
accurately
.
2. Locate an
d mark at lea
st one stud o
n the left or
right side of
the centerline
.
016'
It is importan
t to use at le
ast one wo
od
screw moun
ted firmly in
a stud to su
pport the we
ight
of the microw
ave. Mark tw
o additional, e
venly space
d
locations fo
r the supplie
d toggle bolts
.
3. Drill holes
in the marke
d locations.
Where there
is
a stud, dril
l a 3/16" hole
for wood scr
ews. For hole
s
that do no
t line up with
a stud, drill 5/
8" holes for
toggle bolt
s.
016'
DO NOT IN
STALL THE
MOUNTING
PLATE
AT THIS TIM
E.
4. Remove t
he template f
rom the rear
wall.
5. Review the
Installation In
struction boo
k for your
installation
situation.
Locate and
mark holes
to align with
holes in the
mounting p
late.
IMPORTAN
T:
LOCATE A
T LEAST O
NE STUD
ON EITHE
R SIDE OF
THE CEN
TERLINE
.
MARK THE
LOCATIO
N FOR 2 A
DDITIONAL,
EVENLY
SPACED
TOGGLE
BOLTS IN
THE MOU
NTING PLA
TE
AREA.
Locate and
mark holes
to align with
holes in the
mounting p
late.
IMPORTANT
:
LOCAT
E AT LEAS
T ONE STUD
ON EITH
ER SIDE O
F
THE CENT
ERLINE.
MARK THE
LOCATIO
N FOR 2 A
DDITIONA
L, EVENL
Y
SPACED T
OGGLE BO
LTS IN THE
MOUNTING
PLATE
AREA.
Trim the rear
wall temp
late along
the dotted
line.
Trim the rea
r wall temp
late along t
he dotted l
ine.
%
(%76176(14
*14+<10
6#.
1765+&
'':*#756
%76*1.'6*
417)*4'#
49#..(1
4':*#756
#ਸ਼
12"
4"
Darle vuelta
a la hoja pa
ra consultar
la
versión en E
spañol.
30
1/4"
Minimum
clearance
Plate position-beneath framed recessed cabinet bottom
Your cabinets may have decorative trim that interferes with the microwave installation.
Remove the decorative trim to install the microwave properly and to make it level.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no back or side frame, install the mounting
plate down the same distance as the front overhang depth.
This will keep the microwave level.
1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall an equal distance below the cabinet bottom as
the inside depth of the front overhang.
3. For this type of installation with front overhang only, align the mounting tabs with this
horizontal line, not touching the cabinet bottom as described in Step D.
THE MICROWAVE MUST BE LEVEL.
