Microsemi PowerDsine PD-RPS-1000 Скачать руководство пользователя страница 27

Страница: 27 / 32

Microsemi

Page 27

Rev.A03

Analog Mixed Signal Group

2381 Morse Avenue, Irvine, CA 92614, USA; Phone (USA): (800) 713-4113, ROW: (949) 221-7100 Fax: (949) 756-0308



450W power supply units

PD-9024G/ACDC/M

PD-9012G/ACDC/M

PD-9006ACDC/M

PD-9506G/ACDC/M

PD-55XXG/ACDC/M

WARNING:

When connecting power redundancy connectors, make sure AC power in

both

Midspans is disconnected from AC mains!

8.2 Power Backup

In case one of Midspans' power supplies fails, unit maintains full
functionality by using an optional backup power supply.

Midspan Unit

Redundant Power Supply

PD-9024G/ACDC/M/F
PD-9524G/ACDC/M
PD-9012G/ACDC/M

PD-RPS-1000

PD-9024G/ACDC/M
PD-9006G/ACDC/M
PD-55XXG/ACDC/M

PD-RPS-450

8.3 Connectors

Power backup and power redundancy connectors are located on the back
side of the Midspan.

PD-90xxG power backup and power redundancy have two connectors
(see Figure

8-1):



Power Backup and Power Redundancy Control Signal

connector, RPS COM D-Sub: 15 pins, 3 rows female
connector.



DC Voltage Terminal Block Connector has two positive

(+) terminals and two negative (-) terminals.

Содержание PowerDsine PD-RPS-1000

































Результаты поиска

Содержание PowerDsine PD-RPS-1000

Отзывы:

Похожие инструкции для PowerDsine PD-RPS-1000

Бренды по названию

Популярные бренды

Microsemi PowerDsine PD-RPS-1000, Руководство пользователя

Результаты поиска

Содержание PowerDsine PD-RPS-1000

Отзывы:

Похожие инструкции для PowerDsine PD-RPS-1000

Бренды по названию

Популярные бренды