manualshive.com logo in svg

Micromat MM 470A, Руководство оператора

Поделиться
Скачать
Micromat MM 470A Скачать руководство пользователя страница 9

Section

8

1

ROUTING COMMANDS

DOWN

 (momentary action)

This button enters the position at which the routing cutter is to be fed into the circuit board
along with the setting of the TOOL SWITCH.

If followed immediately by an UP command the cutter will be fed into the board and then
withdrawn, making a single hole the same diameter as the cutter.

If followed by further DOWN commands, with different co-ordinates, the machine will cut
in straight lines between each pair of DOWN co-ordinates.

DOWN may therefore be regarded as a "Down and stay Down" command until an UP is
programmed.

UP

 (momentary action)

The UP command is used to enter the position for the cutter to withdraw the cutter from
the board at the end of a straight line cut. The co-ordinate information entered with the UP
command is irrelevant since the command is used only to lift the cutter but the setting of the
TOOL SWITCH is important since UP commands are used in conjunction with previously
entered DOWN commands using the same TOOL SWITCH number.

NOTE:-  DOWN and UP commands for the same cut must be programmed with the same

     TOOL SWITCH setting.

CUTTING SPEED

The SIL switch is used in the RUN mode to select the cutting speed during routing as
follows:-

10   ..   160 mm/min.
20   ..   175   --
30   ..   190   --
40   ..   210   --
50   ..   240   --
60   ..   275   --
70   ..   320   --
80   ..   385   --
90   ..   480   --
99   ..   645   --

Содержание MM 470A











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды