Microchip Technology Microsemi PolarFire Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 42

Microchip Technology Microsemi PolarFire Скачать руководство пользователя страница 12

PolarFire FPGA 1G Ethernet Loopback Using IOD CDR

Microsemi Proprietary DG0799 Demo Guide Revision 3.0

7

Figure 4 •

CORETSE_0 Configurator

2.3.3.3

pf_init_monitor_0

The pf_init_monitor_0 (PF_INIT_MONITOR) block is used to issue a reset signal to the user logic
(FABRIC_RESET_N). To ensure a glitch-free reset, the DEVICE_INIT_DONE signal is connected to the
CORERESET_PF IP with a lock signal from the PF_CCC macro. The AUTOCALIB_DONE signals the
completion of I/O calibration after which the I/Os can be used. Hence, the AUTOCALIB_DONE and
PLL_LOCK are ANDed and used to reset PF_IOD_CDR_C0_0 and CORETSE_0.

This IP retains the default configuration.

2.3.3.4

Core_reset_pf_0

The Core_reset_pf_0 (CORERESET_PF) block handles the sequencing of reset signals in the PolarFire
device. The CORERESET_PF block synchronizes the reset of all the blocks to which it is connected
when the PolarFire device is powered up.

2.3.3.5

core_jtag_debug_0

The CoreJTAGDebug IP is used to debug the Mi-V soft processor. This IP retains the default
configuration.

«
...
10
11
12
13
14
...
»

Содержание Microsemi PolarFire











































Отзывы:

Нет отзывов