micro-trak MT-2400 LR Скачать руководство пользователя

Страница: 20 / 52

The Universal Switch Box Harness is designed to connect

to your existing boom control switches. The system will

accommodate from one to four boom switches.
Connect the boom harness to the 4-pin M/P connection

on the main harness. Route the cable to the boom control

switches. If more length is needed, extension cables are

available in 5’, 10’, 15’, 20’ and 25’ lengths.
What you want to accomplish is to attach the boom wires

from the MT-2400 harness to the wires on the shut-off valve

harness that are on the solenoid side of the boom switches.

Attach the RED wire to boom 1, the WHITE wire to boom 2,

the GREEN wire to boom 3 and the BLACK wire to boom 4.

See Illustrations 19A and 19B.

Use the moisture resistant tap connectors supplied with the

kit to make the connections.

NOTE: Always turn power to the switches OFF before

installing or removing tap connectors.

Follow these instructions to install moisture resistant tap

connectors:
1. Turn power OFF.
2. Open the hinged side wall of the 3M Scotchlok

™

Tap

Connector and place unstripped boom valve wire inside

run channel. Close hinged side wall.

3. Insert unstripped tap wire completely into tap port.
4. Using pliers, crimp the U-contact flush with the top of

the insulator.

5. Close cover and latch securely.

PLEASE NOTE: The use of moisture resistant tap connectors

(included) is suggested for this kit. If you are not comfortable

with this type of connection, refer to your vehicle’s service

manual for recommended wire splicing instructions.

Installation

(cont)

Universal Switch Box Harness

Illustration 19A

Illustration 19B

Boom 1 (RED)

Boom 2 (WHT)

Boom 3 (GRN)

Boom 4 (BLK)

BOOM

LVE

WIRE

BOOM

LVE

WIRE

-2405F II BOOM DE

WIRE

BOOM

LVE

WIRE

-2405F II BOOM DE

WIRE

BOOM

LVE

WIRE

-2405F II BOOM DE

WIRE

Power

Booms

Connect

to these

Wires

Содержание MT-2400 LR





















































Результаты поиска

Содержание MT-2400 LR

Отзывы:

Похожие инструкции для MT-2400 LR

Бренды по названию

Популярные бренды

micro-trak MT-2400 LR, Справочное руководство

Результаты поиска

Содержание MT-2400 LR

Отзывы:

Похожие инструкции для MT-2400 LR

Бренды по названию

Популярные бренды