
8
9
6)
General power tool safety warnings- Service
• Have your power tool serviced by a qualified repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs.
Service of battery packs should only be
1.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal
injury.
2.
Hold power tool by insulated gripping surfaces, when performing an operation where
the cutting accessory may contact hidden wiring or its own cord.
Cutting accessory
contacting a
″
live
″
wire may make exposed metal parts of the power tool
″
live
″
and
could give the operator an electric shock.
3. Let bit cool before touching, changing or adjusting it. Bits heat up dramatically while in
use, and can burn you.
4. If the drill bit jams, release the Trigger immediately; drill torque can cause injury or break
bit.
5. Avoid unintentional starting. Prepare to begin work before turning on the tool.
6. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
7. When using a handheld power tool, maintain a firm grip on the tool with both
hands to resist starting torque.
8. Do not leave the tool unattended when the Battery Pack is connected. Turn off the tool,
and remove the Battery Pack before leaving.
9. The battery Charger gets hot during use. The Charger’s heat can build up to unsafe
levels and create a fire hazard if it does not receive adequate ventilation, due to an
electrical fault, or if it is used in a hot environment.
Do not place the Charger on a flammable surface.
Do not obstruct any vents on the Charger.
Especially avoid placing the charger on carpets and rugs; they are not only flammable,
but they also obstruct vents under the charger.
Place the Charger on a stable, solid, nonflammable surface (such as a stable metal work-
bench or concrete floor) at least 1 foot away from all flammable objects, such as drapes or
walls. Keep a fire extinguisher and a smoke detector in the area. Frequently monitor the
Charger and Battery Pack while charging.
10. This product is not a toy. Keep it out of reach of children.
11. People with pacemakers should consult their physician(s) before use. Electromagnetic
fields in close proximity to heart pacemaker could cause pacemaker interference or
pacemaker failure.
12. The warnings, precautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product.
• Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpected situations.
7)
Drill safety warnings
is connected.
. Consult the dealer or an experienced radio /TV technician for help.
FCC SAFETY
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause Harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
WARNING: Changes or modification to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
This limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and radiate radio frequency energy
and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communication. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user in encouraged to try to correct the interference by one or more of the
following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
20V ULTRA Drill 2Ah KIT
(MH-03-D-B1-0-1)
20V ULTRA Drill 2Ah KIT
(MH-03-D-B1-0-1)