background image

2

3  

SAFETY DEFINITIONS

This is the safety alert symbol. It is used 

to alert you to potential personal injury 

hazards. Obey all safety messages that follow 

this symbol to avoid possible injury or death.

DANGER  

Indicates an imminently 

hazardous situation which, if not avoided, 

will result in death or serious injury.

WARNING

  Indicates a potentially hazardous 

situation which, if not avoided, could result 

in death or serious injury.

CAUTION

  Indicates an potentially hazardous 

situation which, if not avoided, may result in 

minor or moderate injury.

CAUTION

  used without the safety alert 

symbol indicates a potentially hazardous 

situation which, if not avoided, will result 

in property damage.

1

Never stand or ride on the plow assembly. Keep people and pets at least 25 feet away from the snow plow when in operation. Failure to comply will result in death 

or serious injury.

2

Insert and lock locking pin securely before using. Not doing so will result in serious injury or death. It can also result in damage to the vehicle and/or plow. 

3

Always lower moldboard to the ground when snow plow is being serviced or when vehicle is not in use. 

Failure to comply could result in death or serious 

injury.

4

The Path Pro

2

 is for driveway plowing only and should be used on ½-ton and smaller vehicles. Use of this product on larger than ½-ton vehicles is prohibited and can result in 

damage to the vehicle or plow. Failure to comply could result in death or serious injury.

5

NEVER

 use the Path Pro

2

 without first CAREFULLY reading the Owner’s Manual. It is CRITICAL for your safety to ALWAYS obey EVERY warning in the manual and follow 

EVERY instruction EXPLICITLY. Failure to comply could result in death or serious injury.

6

The Path Pro

2

 by Meyer should be used by drivers with a valid operator’s license. Keep all body parts inside the vehicle. Failure to comply could result in death or serious injury.

7

To prevent accidental movement of the plow, always turn off the controller whenever the plow is not in use. Failure to comply could result in death or serious injury.

8

The Path Pro

2

 should NEVER be used for ANY other purpose other than plowing snow on a driveway, using the Path Pro

2

 for other purposes could result in serious injury 

or death. 

9

Inspect plow assembly and mounting components and fasteners for wear and damage before and after each use. Worn or damaged components or fasteners could 

allow the plow to drop unexpectedly. Failure to comply could result in death or serious injury.

10

Do not change plow position while traveling. You could suddenly lower the plow accidentally. Failure to comply could result in death or serious injury.

11

ALWAYS wear a seat belt when plowing snow. Hidden obstructions can cause the vehicle to stop suddenly resulting in personal injury. Failure to comply could 

result in death or serious injury.

12

Do not mix different kinds of hydraulic fluid. Some fluids are not compatible and may cause performance problems and product damage Failure to comply could 

result in death or serious injury.

13

NEVER perform any repairs or maintenance with the plow controller turned on and the plow plugged into the vehicle harness and the plow attached to the vehicle. 

Failure to comply could result in death or serious injury. 

14

The vehicle must not be operated when overloaded. In all cases, the loaded vehicle weight, including the entire snow plow system, all aftermarket accessories, driver, passenger, 

options, nominal fluid levels, and cargo must not exceed the front/rear Gross Axle Weight Rating (GAWR), and total Gross Vehicle Weight Rating (GVWR). These weights ratings 

are specified on the safety compliance certification label on the driver’s side door opening. The use of rear ballast weight may be required to prevent exceeding the front GAWR.   

Failure to comply could result in death or serious injury.

15

Read the 

Path Pro

2

 Owner’s Manual before operating or servicing a snow plow. 

FOLLOW THESE INSTRUCTIONS EXPLICITLY. 

Failure to comply could result in 

death or serious injury.

16

SAFETY PRECAUTIONS

 should be used when Hydraulic Unit is in OPERATION and plow is in a RAISED position. Lower plow to ground when vehicle is PARKED in case 

of hydraulic failure. Failure to comply could result in death or serious injury. 

Содержание Path Pro2













































Отзывы: