background image

4

5  

SAFETY DEFINITIONS

This is the safety alert symbol. It is used 

to alert you to potential personal injury 

hazards. Obey all safety messages that follow 

this symbol to avoid possible injury or death.

DANGER  

Indicates an imminently 

hazardous situation which, if not avoided, 

will result in death or serious injury.

WARNING

  Indicates a potentially hazardous 

situation which, if not avoided, could result 

in death or serious injury.

CAUTION

  Indicates an potentially hazardous 

situation which, if not avoided, may result in 

minor or moderate injury.

CAUTION

  used without the safety alert 

symbol indicates a potentially hazardous 

situation which, if not avoided, will result 

in property damage.

17

Remove Plow Assembly before placing vehicle on hoist/lift. Failure to comply could result in death or serious injury.

18

Do not exceed 10 mph transporting plow. Do not exceed 5 mph plowing snow. Know your  road conditions at all times. Keep feet clear of moldboard at all times.  

Failure to comply could result in death or serious injury.

19

SAFETY PRECAUTIONS

 should be used when Hydraulic Unit is SERVICED. Hydraulic fluid under pressure can cause skin injection injury. If you are injured by hydraulic 

fluid, get medical attention immediately. Failure to comply could result in death or serious injury.

20

Vehicle exhaust contains lethal fumes. Breathing these fumes, even in low concentrations, can cause death. Never operate vehicle in an enclosed area without venting the 

exhaust to the outside. Failure to comply could result in death or serious injury.

21

Gasoline is highly flammable and gasoline vapor is explosive. Never smoke while working on vehicle. Keep all open flames away from gasoline tank and lines.  

Wipe up any spilled gasoline immediately. Failure to comply could result in death or serious injury.

22

Flag obstructions that are under snow to prevent damage to product or property. Failure to comply may result in minor or moderate injury.

23

A ballast weight may be required to prevent front GAWR overloading. If required, ballast must be securely attached at least 24 inches behind the rear axle. Failure to 

comply will result in property damage.

24

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lit tobacco to come near the battery. When charging 

or working near a battery, always cover your face and protect your eyes, and also provide ventilation. Batteries contain sulfuric acid which burns skin, eyes and clothing.  

Failure to comply will result in property damage.

25

See your  Path Pro

2

 Authorized Distributor/Web site for specific vehicle application recommendations before installation. Failure to comply will result in property 

damage.

26

Installation of a snow plow may affect your new vehicle warranty.  For more information consult your Vehicle Owner’s Manual / Vehicle Dealer. Failure to comply will 

result in property damage.

27

Warranty does not apply to a  Path Pro

2

 product which has been negligently or improperly assembled or installed. Failure to comply will result in property damage.

28

CAUTION: 

To avoid harm to vehicles electrical system always disconnect battery before beginning installation. 

DO NOT BURN

 holes or 

WELD

 vehicle frame.  

This may cause frame failure. Failure to comply will result in property damage.

29

A driver’s first responsibility is the safe operation of the vehicle and snow plow. The most important thing you can do to prevent a crash is to avoid distractions and pay 

attention to the road. Wait until it is safe to operate mobile communication equipment such as cell phones, two way radios, etc. Failure to comply will result in property 

damage.

30

Front end wheel alignment and headlight aim may require readjustment after installation of equipment, and is the responsibility of the equipment installer. Failure 

to adjust front wheel alignment may cause premature uneven tire wear. If required, reset to chassis manufacture’s specifications. Failure to comply will result in 

property damage.

Содержание Path Pro2













































Отзывы: