background image

SAFETY DEFINITIONS

This is the safety alert symbol. It is used 

to alert you to potential personal injury 
hazards. Obey all safety messages that 
follow this symbol to avoid possible 
injury or death.

DANGER  Indicates an imminently 

hazardous situation which, if not 
avoided, will result in death or serious 
injury.

WARNING  Indicates a potentially 

hazardous situation which, if not 
avoided, could result in death or serious 
injury.

CAUTION  Indicates an potentially 

hazardous situation which, if not 
avoided, may result in minor or 
moderate injury.

CAUTION  used without the safety 

alert symbol indicates a potentially 
hazardous situation which, if not 
avoided, will result in property 
damage.

2

17

Remove Plow Assembly before placing vehicle on hoist/lift. Failure to comply could result in death or serious injury.

18

Do not exceed 16 kph transporting plow. Do not exceed 8 kph plowing snow. Know your  road conditions at all times. Keep feet clear of moldboard 
at all times. Failure to comply could result in death or serious injury.

19

SAFETY  PRECAUTIONS should be used when Hydraulic Unit is SERVICED. Hydrauilic fluid under pressure can cause skin injection injury. If you are 
injured by hydraulic fluid, get medical attention immediately. Failure to comply could result in death or serious injury.

20

Vehicle  exhaust contains lethal fumes. Breathing these fumes, even in low concentrations, can cause death. Never operate vehicle in an enclosed area 
without venting the exhaust to the outside. Failure to comply could result in death or serious injury.

21

Gasonline is highly flamable and gasoline vapor is explosive. Never smoke while working on vehicle. Keep all open flames away from gasoline tank 
and lines. Wipe up any spilled gasoline immediately. Failure to comply could result in death or serious injury.

22

Flag obstructions that are under snow to prevent damage to product or property. Failure to comply may result in minor or moderate injury.

23

A ballast weight may be required to prevent front GAWR overloading. If required, ballast must be securely attached at least 61 cm behind the 
rear axle. Failure to comply will result in property damage.

24

Batteries  normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lit tobacco to come near the 
battery. When charging or working near a battery, always cover your face and protect your eyes, and also provide ventilation. Batteries contain sulfuric 
acid which burns skin, eyes and clothing. Failure to comply will result in property damage.

25

See your Meyer Authorized Distributor/Web site for specific vehicle application recommendations before installation. Failure to comply will result in 
property damage.

26

Installation of a snow plow may affect your new vehicle warranty.  For more information consult your Vehicle Owner’s Manual / Vehicle Dealer. 
Failure to comply will result in property damage.

27

Warranty does not apply to a Meyer product which has been negligently or improperly assembled or installed. Failure to comply will result in 
property damage.

28

CAUTION: To avoid harm to vehicles electrical system always disconnect battery before beginning installation. DO NOT BURN holes or WELD vehicle 
frame. This may cause frame failure. Failure to comply will result in property damage.

29

A driver’s first responsibility is the safe operation of the vehicle and snow plow. The most important thing you can do to prevent a crash is to avoid 
distractions and pay attention to the road. Wait until it is safe to operate mobile communication equipment such as cell phones, two way radios, etc. 
Failure to comply will result in property damage.

30

Front end wheel alignment and headlight aim may require readjustment after installation of equipment, and is the responsibility of the 
equipment installer. Failure to adjust front wheel alignment may cause premature uneven tire wear. If required, reset to chassis manufacture’s 
specifications. Failure to comply will result in property damage.

Содержание Drive Pro LD



























Отзывы: