manualshive.com logo in svg

Mettler Electronics Sys*Stim 294, Инструкция по эксплуатации

Поделиться
Скачать
Mettler Electronics Sys*Stim 294 Скачать руководство пользователя страница 34

Mettler Electronics Corp.—

 

Rev.F_09/13/17 

34

 

 

If E7 occurs when the output is first being 
adjusted, it may mean the electrodes or cables are 
not making a good circuit. Check cable and 
electrode connections and make sure electrodes 
are making good contact with the patient. 
In the continuous treatment modes the output 
voltage is reduced while the unit monitors the 
impedance of the patient connection. If the unit is 
in amplitude modulated modes, such as recip or 
surge, this patient connection error causes the unit 
to go into the HOLD mode. 
All patient connection errors should be 
investigated to determine their cause. 

4.

 

“E80_” displayed in Time 
window. 

An output overcurrent has been detected. Current 
exceeded 70 mA RMS for interferential, 55 mA for 
premodulated, and medium frequency or 105 mA 
peak for biphasic. 
Reposition electrodes farther apart. Remove any 
moisture or gel from between the electrodes and 
try again.  If error persists even without a patient 
connection or load, unit requires servicing. 

5.

 

“E90_” displayed in Time 
window. 

Output error for electrical stimulation has been 
detected. Remove electrode cables from unit and 
restart. Replace electrode cables onto unit. 
Reprogram treatment and try starting treatment 
session again. 
If powering unit OFF and restarting does not 
remove error, the unit requires servicing. 

6.

 

“F1__” displayed in Time 
window. 

There has been a communication error between 
the microprocessors. If powering unit OFF and 
restarting does not remove error, unit requires 
servicing. 

7.

 

“F2__” displayed in Time 
window. 

There has been a self-test error— If powering unit 
OFF and restarting with all the electrode cables 
removed does not remove error, the unit requires 
servicing. 

8.

 

“F3   _” displayed in Time 
window. 

There has been a power supply error— If 
powering unit OFF and restarting does not 
remove error, the unit requires servicing. 

If problem is not addressed above, or if additional troubleshooting guidance is desired, 
call (800) 854-9305 or email service directly at 

[email protected]

. 

The distributor who sold the Sys*Stim 294 should be able to assist you with a loaner unit 

during warranty service. 

Содержание Sys*Stim 294













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды