Metso Switchguard SG9000H Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 48

background image

8

7 SG9H 70 en

3.4

Mounting and installation of SG9300

Mounting bracket



Make sure the mounting bracket is suitable for the
weight of the device. See detailed weight informa-
tion in Section 1.5.



Three extra M8 mounting holes exist in the standard
mounting face of the housing for additional support. See
dimension drawings for SG9300 in pages 40-41 (Chapter
12). The use of this extra support is mandatory in addition
to the standard mounting face.



There are also two 6.5 mm holes for additional sup-
port when needed. See dimension drawings for
SG9300 in pages 40-41 (Chapter 12).

Pipeline support



Due to the extra weight of stainless steel version
and/or possible heavy vibration, make sure there are
proper supports in the pipeline to hold the weight of
the valve assembly.

Spool valve protective cover



The spool valve protective cover (454) has 2 pcs. of
1/2” NPT threaded openings.



Openings allow an adequate exhaust capacity and
breathing of the spool valve.



Openings have breathers (456) installed, but they
can be replaced with protective piping if needed
and when necessary.



If SG is installed vertically, it is recommended to
replace the breather with protective piping in the
opening pointing upwards.

Exhaust adapter



The exhaust adapter (8) has a 1/2” NPT threaded
opening.



Opening allows an excess air to be released from the
housing and to prevent overpressurization.



Exhaust adapter has a breather (456) installed, but it
can be replaced with protective piping if needed
and when necessary.



Opening in the exhaust adapter shall not be
plugged!

Protective piping



Piping of the spool valve cover and/or exhaust
adapter shall be done in cases where it is assumed
that water can go inside the spool valve cover or into
the exhaust adapter in spite of breathers.



Piping shall be done so that the blowing of the exhaust
air is downwards and to prevent water to go inside the
protective cover or the exhaust adapter.



Minimum inside diameter of the piping is 13 mm.



Exhaust adapter piping shall not be connected to
the spool valve cover piping!

NOTE:

These instructions are only for the mounting and installa-
tion of SG9300, i.e. stainless steel version of SG9000H.

Fig. 4

Shaft coupling alternatives

45°

45°

45°

45°

SG93

SG92

VDI/VDE 3845 mounting

IEC 60534 mounting

SHAFT ENDS

pointer

pointer

marks
on housing

marks

on housing

«
...
6
7
8
9
10
...
»

Содержание Switchguard SG9000H

















































Отзывы:

Нет отзывов

Похожие инструкции для Switchguard SG9000H

Бренд: Vacon Страницы: 62

Бренд: EA Страницы: 24

Бренд: B&R Industries Страницы: 89

Бренд: National Instruments Страницы: 29

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: olympia electronics Страницы: 10

Бренд: Parker Страницы: 12

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 2

Бренд: IBA Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды