background image

 

 

Page 25 of 25 

 

Open the printer door by pressing the door latch 
inwards. 
Place forefinger against the lower edge of the 
mechanism mounting chassis and thumb against 
the base of the door (see Figure 6). 
 
 
Carefully press the door and chassis in vertically 
opposite directions until the catch is released.  Do 
not pull the door and chassis apart without first 
releasing the catch. 
Swing the chassis back, leaving the door fully 

open.  This will expose the printer mechanism 
and ink ribbon cartridge. 
Press down on the end of the ink ribbon cartridge 
marked 'PUSH' (see Figure 7) and carefully 
remove the used cartridge.  
 
Fit a replacement cartridge, ensuring that the 
paper lies between the ribbon and the steel 
printer platen.  
 

 
 
 
 
 
 
Check that the ribbon cartridge spindle is 
correctly seated over the printer ribbon drive 
shaft, and snap the cartridge into place.   

Ensure that the ribbon is taut and parallel to the 
paper.   
If necessary tighten the ribbon by turning the 
faceted disc clockwise using fingernail (see 
Figure 8). 

 

If there is some paper protruding from the front of 
the printer mechanism, ensure that it will pass 
clearly through the guide channel and past the 
tear bar before snapping the chassis shut against 
the back of the door. 
 
Turn the paper roll by hand so that any loose 
turns are wound snugly against the roll.   
Close the door and check that the paper flows 
freely, using the paper feed button. 
 
For paper and printer ribbon refills, contact the 
Metron Inc. factory. 

 

Содержание MP430 Series


































Отзывы: