background image

 

 

Page 21 of 25 

 

Configure User Preferences 
(continued)

 

 
 
 

 

 

 

213 USER PREFERENCES 
 High Discharge Pressure 
Alarm Pressure 
[185] psi          0-999

 

 

The pressure at or above which will cause a High Pressure alarm condition 

 

 

 

214 USER PREFERENCES 

 High Discharge Alarm 
Pressure Time Delay 
[ 5]seconds      0-99 

 

The amount of time the pressure must be at or above the set pressure before the 
alarm condition is activated. 

 

 

 

215 USER PREFFENCES 
  Low Discharge Pressure 
 Alarm Option 
[No]   

 

 

This setting is used to monitor the system pressure and turn on the LOW 
PRESSURE LED and sound an alarm if it drops below a preset pressure. 

 

 

 

216 USER PREFERENCES 
 Low Discharge Pressure 
Alarm Pressure 
[45] psi          0-999

 

 

The pressure at or below which will cause a Low Pressure alarm condition 

 

 

 

217 USER PREFERENCES 

 Low Discharge Alarm 
Pressure Time Delay 
[ 5]seconds      0-99 

 

The amount of time the pressure must be at or below the set pressure before the 
alarm condition is activated. 

 

 

 

218 USER PREFERENCES 

 No Load Amps % 
 Of FLA 
[10]             0-99 

 

The % of  motor full load current at which or below that will cause an event to be 
logged indicating a No Load Motor Condition. 

 

 

 

218 USER PREFERENCES 

 No Load Time 
 Delay 
[ 5]seconds      0-99 

 

The amount of time the motor current must be at or below the set level before the 
event condition is logged. 

 

 

 

220 USER PREFERENCES 
LCD Back Light Mode 
        0=Always on 
[0]]    1=Power Save

 

 

Set to Always on or to Power Save if it is desired to have the backlight 
automatically shut off when no buttons have been pressed for a preset period of 
time.  

 

 

 

221 USER PREFERENCES 
Language Select 
 
[English]

 

 

Set to English or Spanish 

 

 

 

222 USER PREFERENCES 
Change User Password 
Level 1 
[****]

 

 

Used to set the password necessary to access the System config screens. 

 

 

 

223 USER PREFERENCES 
Reversed Phase 
Order (1-3-2) 
[No] 

 

Used to change the phase sequence sensing of the incoming power. If a Phase 
reversal alarm occurs on initial installation and the motor is turning the correct 
direction, change this setting to YES to reset the alarm indication. 

 

Содержание MP430 Series


































Отзывы: