METRON FD4 Скачать руководство пользователя

Страница: 30 / 34

Page 30 of 34

File Name:

Doc#586p.docx

Real Time Event Monitoring:

All events listed below in figure 1.2 are real time and can be viewed in Modbus register 40002. Figure 1.2 depicts the 16 bit
breakdown and cross reference. This is not to be confused with the historical event log.

Figure 1.2

Description

Modbus Registers

Usage Notes For Read Only Registers

Bit 0 'Switch In Auto'

040002:0

Bit 0 Of Modbus Register 040002 - Indicates the 'Switch In Auto' Event

Bit 1 'System Fault'

040002:1

Bit 1 Of Modbus Register 040002 - Indicates The 'System Fault' Event

Bit 2 'Engine Running'

040002:2

Bit 2 Of Modbus Register 040002 - Indicates The 'Engine Running' Event

Bit 3 'Battery Fault'

040002:3

Bit 3 Of Modbus Register 040002 - Indicates The 'Batter Fault' Event

Bit 4 'Charger Failure'

040002:4

Bit 4 Of Modbus Register 040002 - Indicates The ''Charger Failure' Event

Bit 5 'Failed To Start'

040002:5

Bit 5 Of Modbus Register 040002 - Indicates The 'Failed To Start' Event

Bit 6 'AC Power Failure'

040002:6

Bit 6 Of Modbus Register 040002 - Indicates The 'AC Power Failure' Event

Bit 7 'Low Oil Pressure'

040002:7

Bit 7 Of Modbus Register 040002 - Indicates the 'Low Oil Pressure' Event

Bit 8 'High Water Temperature'

040002:8

Bit 8 Of Modbus Register 040002 - Indicates The 'High Water Temperature' Event

Bit 9 'Low Fuel Level'

040002:9

Bit 9 Of Modbus Register 040002 - Indicates The 'Low Fuel Level' Event

Bit 10 'Pump On Demand'

040002:10

Bit 10 Of Modbus Register 040002 - Indicates The 'Pump On Demand' Event

Bit 11 'Engine Overspeed'

040002:11

Bit 11 Of Modbus Register 040002 - Indicates The 'Engine Overspeed' Event

Bit 12 'Engine Quit'

040002:12

Bit 12 Of Modbus Register 040002 - Indicates The 'Engine Quit' Event

Bit 13 'Low Discharge Pressure'

040002:13

Bit 13 Of Modbus Register 040002 - Indicates A 'Low Discharge Pressure' Event

Bit 14 'Engine Fuel Solenoid On'

040002:14

Bit 14 Of Modbus Register 040002 - Indicates A 'Engine Fuel Solenoid On' Event

Bit 15 'High Discharge Pressure'

040002:15

Bit 15 Of Modbus Register 040002 - Indicates A 'High Discharge Pressure' Event
**All Data In Modbus Register 40002 Is Real Time**

Description

Modbus Registers

Usage Notes For Read Only Registers

Bit 0 'Pressure Transducer Fault'

040003:0

Bit 0 Of Modbus Register 040003 - Indicates the 'Pressure Transducer Fault' Event

Bit 1 'Low Intake'

040003:1

Bit 1 Of Modbus Register 040003 - Indicates The 'Low Intake' Event

Bit 2 'Switch in Manual'

040003:2

Bit 2 Of Modbus Register 040003 - Indicates The 'Switch in Manual' Event

Bit 3 'Switch in Off'

040003:3

Bit 3 Of Modbus Register 040003 - Indicates 'Switch in Off' Event

Bit 4 'Battery 1 Failure'

040003:4

Bit 4 Of Modbus Register 040003 - Indicates The 'Battery 1 Failure' Event

Bit 5 'Battery 2 Failure'

040003:5

Bit 5 Of Modbus Register 040003 - Indicates The 'Battery 2 Failure' Event

Bit 6 'Charger 1 Failure'

040003:6

Bit 6 Of Modbus Register 040003 - Indicates The 'Charger 1 Failure' Event

Bit 7 'Charger 2 Failure'

040003:7

Bit 7 Of Modbus Register 040003 - Indicates The 'Charger 2 Failure' Event

Bit 8 'Pressure Drop'

040003:8

Bit 8 Of Modbus Register 040003 - Indicates The 'Pressure Drop' Event

Bit 9 'Engine Auto Available'

040003:9

Bit 9 Of Modbus Register 040003 - Indicates The 'Engine Auto Start Available' Event

Bit 10 'Contactor Coil Failure'

040003:10

Bit 10 Of Modbus Register 040003 - Indicates The 'Common Contactor Coil Failure' Event

Bit 11 'Test Running'

040003:11

Bit 11 Of Modbus Register 040003 - Indicates The 'Engine Running in Test Mode' Event

Bit 12 'Hi/Low Zone'

040003:12

Bit 12 Of Modbus Register 040003 - Indicates The 'High/Low Zone Event

Bit 13 'Contactor Coil 1 Failure'

040003:13

Bit 13 Of Modbus Register 040003 - Indicates A 'Contactor Coil 1 Failure' Event

Bit 14 'Contactor Coil 2 Failure'

040003:14

Bit 14 Of Modbus Register 040003 - Indicates A 'Contactor Coil 2 Failure' Event

Bit 15 'Weekly Test Due'

040003:15

Bit 15 Of Modbus Register 040003 - Indicates A 'Weekly Test Due' Event
**All Data In Modbus Register 40003 Is Real Time**

Description

Modbus Registers

Usage Notes For Read Only Registers

Bit 0 'Dump Valve'

040004:0

Bit 0 Of Modbus Register 040004 - Indicates 'Dump Valve On' Event

Bit 1 'Engine Lockout'

040004:1

Bit 1 Of Modbus Register 040004 - Indicates 'Engine Lockout' Input

Bit 2 'Stop Push button'

040004:2

Bit 2 Of Modbus Register 040004 - Indicates 'Stop push button pressed' Event

Bit 3 'SD Card Missing'

040004:3

Bit 3 Of Modbus Register 040004 - Indicates ' SD Card Missing' Event

Bit 4 'Reset button'

040004:4

Bit 4 Of Modbus Register 040004 - Indicates 'Reset push button pressed' Event

Bit 5 'OID LED 13'

040004:5

Bit 5 Of Modbus Register 040004 - Indicates 'OID Lamp 13 on'

Bit 6 'OID LED 14'

040004:6

Bit 6 Of Modbus Register 040004 - Indicates 'OID Lamp 14 on'

Bit 7 'OID LED 15'

040004:7

Bit 7 Of Modbus Register 040004 - Indicates 'OID Lamp 15 on/ECM Failure'

Bit 8 'OID LED 16'

040004:8

Bit 8 Of Modbus Register 040004 - Indicates 'OID Lamp 16 on/EMC Warning'

Bit 9 'OID LED 17'

040004:9

Bit 9 Of Modbus Register 040004 - Indicates 'OID Lamp 17 on/ECM Switch in Alt.'

Bit 10 'OID LED 18'

040004:10

Bit 10 Of Modbus Register 040004 - Indicates 'OID Lamp 18 on/Fuel Injection Fault'

Bit 11 'OID LED 19'

040004:11

Bit 11 Of Modbus Register 040004 - Indicates 'OID Lamp 19 on/Fual Tank Leak'

Bit 12 'OID LED 20'

040004:12

Bit 12 Of Modbus Register 040004 - Indicates 'OID Lamp 20 on/Clogged Water Strainer'

Bit 13 'OID LED 21'

040004:13

Bit 13 Of Modbus Register 040004 - Indicates 'OID Lamp 21 on/High Cooling Water Temp.'

Bit 14 'OID LED 22'

040004:14

Bit 14 Of Modbus Register 040004 - Indicates 'OID Lamp 22 on/Low Engine Temp.'

Bit 15 'OID LED 23'

040004:15

Bit 15 Of Modbus Register 040004 - Indicates 'OID Lamp 23 on/Contactor Coil Failure'
**All Data In Modbus Register 40004 Is Real Time**

Description

Modbus Registers

Usage Notes For Read Only Registers

Bit 0 'R1'

040005:0

Bit 0 Of Modbus Register 040005 - Indicates 'Relay 1 On'

Bit 1 'R2'

040005:1

Bit 1 Of Modbus Register 040005 - Indicates 'Relay 2 On'

Bit 2 'R3'

040005:2

Bit 2 Of Modbus Register 040005 - Indicates 'Relay 3 On'

Bit 3 'R4'

040005:3

Bit 3 Of Modbus Register 040005 - Indicates 'Relay 4 On' - Horn

Bit 4 'R5'

040005:4

Bit 4 Of Modbus Register 040005 - Indicates ' Relay 5 On' - Drain Solenoid

Bit 5 'R6'

040005:5

Bit 5 Of Modbus Register 040005 - Indicates 'Relay 6 On' - Engine Fuel Solenoid

Bit 6 'R7'

040005:6

Bit 6 Of Modbus Register 040005 - Indicates 'Relay 7 On' - Engine Stop Solenoid

Bit 7 'R8'

040005:7

Bit 7 Of Modbus Register 040005 - Indicates 'Relay 8 On'

Bit 8 'R9'

040005:8

Bit 8 Of Modbus Register 040005 - Indicates 'Relay 9 On' - System Fault (US mode)

Bit 9 'R10'

040005:9

Bit 9 Of Modbus Register 040005 - Indicates 'Relay 10 On' - Engine Running (US mode)

Bit 10 'R11'

040005:10

Bit 10 Of Modbus Register 040005 - Indicates 'Relay 11 On'

Bit 11 'R12'

040005:11

Bit 11 Of Modbus Register 040005 - Indicates 'Relay 12 On' Auto mode on (EU Mode)

Bit 12 'R13'

040005:12

Bit 12 Of Modbus Register 040005 - Indicates 'Relay 13 On'

Bit 13 'R14'

040005:13

Bit 13 Of Modbus Register 040005 - Indicates 'Relay 14 On' Engine running (EU Mode)

Bit 14 'R15'

040005:14

Bit 14 Of Modbus Register 040005 - Indicates 'Relay 15 On' Engine running (EU Mode)

Bit 15 'R16'

040005:15

Bit 15 Of Modbus Register 040005 - Indicates 'Relay 16 On' Pump on demand (EU Mode)
**All Data In Modbus Register 040005 Is Real Time**

Description

Modbus Registers

Usage Notes For Read Only Registers

Bit 0 'R17'

040006:0

Bit 0 Of Modbus Register 040006 - Indicates 'Relay 17 On' Failed to start (EU Mode)

Bit 1 'R18'

040006:1

Bit 1 Of Modbus Register 040006 - Indicates 'Relay 18 On' System Fault (EU Mode)

Bit 2 'R19'

040006:2

Bit 2 Of Modbus Register 040006 - Indicates 'Relay 19 On'

Bit 3 'R20'

040006:3

Bit 3 Of Modbus Register 040006 - Indicates 'Relay 20 On'

Bit 4 'R21'

040006:4

Bit 4 Of Modbus Register 040006 - Indicates ' Relay 21 On'

Bit 5 'R22'

040006:5

Bit 5 Of Modbus Register 040006 - Indicates 'Relay 22 On'

Bit 6 'R23'

040006:6

Bit 6 Of Modbus Register 040006 - Indicates 'Relay 23 On'

Bit 7 'R24'

040006:7

Bit 7 Of Modbus Register 040006 - Indicates 'Relay 24 On'

Bit 8 'Auto Test'

040006:8

Bit 8 Of Modbus Register 040006 - Indicates 'Test mode initiated but not running'

Bit 9 'Cranking'

040006:9

Bit 9 Of Modbus Register 040006 - Indicates 'Cranking engine'

Bit 10 'Start by remote'

040006:10

Bit 10 Of Modbus Register 040006 - Indicates 'Engine started running after remote start'

Bit 11 'Remote Start Input'

040006:11

Bit 11 Of Modbus Register 040006 - Indicates 'Remote start input present'

Bit 12 'Remote Start'

040006:12

Bit 12 Of Modbus Register 040006 - Indicates 'Remote start was received'

Bit 13 'Shutdown in test'

040006:13

Bit 13 Of Modbus Register 040006 - Indicates 'Engine stopped during test run due to alarm'

Bit 14

040006:14

Bit 14 Of Modbus Register 040006 - NOT USED

Bit 15

040006:15

Bit 15 Of Modbus Register 040006 - NOT USED
**All Data In Modbus Register 040006 Is Real Time**

Содержание FD4



































Результаты поиска

Содержание FD4

Отзывы:

Похожие инструкции для FD4

Бренды по названию

Популярные бренды

METRON FD4, Руководство пользователя

Результаты поиска

Содержание FD4

Отзывы:

Похожие инструкции для FD4

Бренды по названию

Популярные бренды