Metrohm 757 VA Computrace Скачать руководство пользователя страница 25

Страница: 25 / 82

3.3 Multi-mode electrode (MME)

757 VA Computrace – Hardware

3.3

Multi-mode electrode (MME)

The multi-mode electrode combines the most important polarographic and volt-

ammetric mercury electrodes in a single construction:

•

HMDE

Hanging mercury drop electrode

Mercury is forced through a glass capillary until a drop

forms at the capillary tip and the entire voltage sweep

performed on this single stationary drop; in general

with preceding enrichment (stripping voltammetry).

•

DME

Dropping mercury electrode

The classical electrode, the mercury drops fall from the

glass capillary at a controlled rate.

•

SMDE

Static mercury drop electrode

The latest electrode, it combines the features of the

DME and the HMDE: during the measurement, the

drop surface is constant and stationary (as with the

HMDE); however, for the complete voltage sweep sev-

eral drops are needed (renewal as with the DME).

3.3.1

Construction and operating characteristics of the MME

The construction of the 6.1246.020 Multi-mode electrode is shown in

Fig. 8

. The

mercury in the reservoir

flows through the glass capillary

forming a drop at its

end. The mercury flow is controlled by the sealing needle

, which can be raised

or lowered pneumatically. The different types of electrodes (HMDE, DME, SMDE)

are implemented by timed opening or closing of the mercury flow using this sealing

needle.
The operating characteristics of the MME are illustrated by

Figs. 7

and

. After valve

(inert gas supply) is opened, the mercury in the reservoir

is pressurized. In

the standby mode, a back pressure is built up in the interior of the slotted screw

which causes the built-in spring to press the sealing needle

onto the capillary

opening of the glass capillary

thus preventing the outflow of mercury. Switching

the valve

allows the inert gas to escape thus releasing the back pressure. The

inert gas pressure in the mercury reservoir

presses the sealing needle

fixed

to the PTFE membrane of the slotted screw

upwards and the mercury can now

flow out. The tapping mechanism of the DME and SMDE is triggered by brief open-

ing and closing of valve

The mercury drops formed at the end of the capillary are very small and stable and

thus afford a very good signal/noise ratio. The mercury hermetically sealed in the

reservoir comes into contact only with inert gas and other inert materials and suf-

fices for around 200'000 drops.

Содержание 757 VA Computrace



















































































Результаты поиска

Содержание 757 VA Computrace

Отзывы:

Бренды по названию

Популярные бренды

Metrohm 757 VA Computrace, Руководство по оборудованию

Результаты поиска

Содержание 757 VA Computrace

Отзывы:

Бренды по названию

Популярные бренды