Metrohm 2.942.0500 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 63

Metrohm 2.942.0500 Скачать руководство пользователя страница 27

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭

3 Installation

942 Extension Module Vario SeS/PP (2.942.0500)

￭￭￭￭￭￭￭￭

19

6.1803.030

6.2744.070

6.2744.034

6.1826.xx0

6.2744.180

6.2744.070

Suppressor

On the pump tubing's …

… connect this accessory

Entry

Tighten the aspiration tubing (6.1803.030) to the tubing olive (6.2744.034)
using a pressure screw (6.2744.070).

Exit

Tighten the

rinsing solution

suppressor capillary to the pump tubing con-

nection with locking nut and filter (6.2744.180) using a pressure screw
(6.2744.070).

Next steps

￭

Connect the loose end of the aspiration capillary to the bottle with the
rinsing solution.

Setting the flow rate

The flow rate of the peristaltic pump depends on many factors:

￭

The inner diameter of the pump tubing

￭

The rotational speed of the drive

￭

The contact pressure of the tubing cartridge

NOTICE

Pieces of pump tubing are consumables. The service life of the pump
tubing depends on the contact pressure, among other factors.

«
...
25
26
27
28
29
...
»

Содержание 2.942.0500
































































Отзывы:

Нет отзывов