Metos 74GFREBM, Инструкция по установке и эксплуатации

Страница: 31 / 36

|
31
EDITION 001 2028
METOS PROXY GAS FRYERS
10. FUMES EXHAUST SYSTEM
Provide a fumes exhaust system based on the “Type” of app-
liance.The “Type” is stated on the appliance dataplate. .
APPLIANCE TYPE “A1”
• Position the “A1” type appliance below an extractor hood to
ensure smoke and fumes generated by cooking are removed.
APPLIANCE TYPE “B21”
• Position the “B21” type appliance below an extractor hood.
APPLIANCE TYPE “B11”
• Fit the “B11” type appliance with a suitable fl ue, available
from the appliance manufacturer. Follow the assembly in-
structions provided with the
fl ue.
• Connect the fl ue to a 150/155 mm diameter hose, heat resis-
tant to 300°C.
• Vent to the outside or into an e ffi cient fl ue. The hose length
must not exceed 3 metres.
11. CONNECTIONS
The position and dimensions of connections are given in the
installation diagram at the start of this manual.
CONNECTION TO THE GAS SUPPLY
Check the compatibility of the gas supply. Check the details
given on the decals on the packing and on the appliance. If
necessary, convert the appliance to the type of gas utilized.
Follow the instructions in the next paragraph “Conversion to a
di
ff erent type of gas”.
On top appliances a rear connection is also available. Remove
the plug present and screw it tightly onto the front connector.
• A rapid-action gas shut-o ff valve must be fi tted upstream of
the appliance in an easily accessible position.
• Do not use connection pipes having a diameter smaller than
that of the appliance’s gas connector.
• Once the appliance has been installed, check for leaks at the
connection points.
12 CONVERSION TO A DIFFERENT TYPE OF GAS
Table T1 speci fi es, for each country:
• which gas can be used for the appliance.
• the nozzles and settings foreach gas that can be used.For
nozzles, the number indicated in table T1 is also stamped on
the nozzle body.
To convert the appliance to the local gas type, follow the instruc-
tions given in atable T1 and carry out the steps elow:
• Replace the main burner nozzle ( UM ).
• Adjust the main burner’s air regulator to distance A.
• Replace the pilot burner nozzle ( UP ).
• Adjust the pilot burner air
fl ow ( if necessary ).
• Replace the gas valve minimum nozzle ( Um ).
• A
ffi x the adhesive tab indicating the new type of gasused.The
nozzles and adhesive tabs are suppliedwith the appliance.
Instructions for installation
REMINDERS FOR THE INSTALLER
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Installation, conversion to a di ff erent type of gas and appli-
ance maintenance must be carried out by quali fi ed techni-
cians authorized by the manufacturer, in compliance with
current safety standards and the instructions given in this
manual.
• Identify the speci fi c appliance model. The model number is
detailed on the packaging and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the appli-
ance.
• Do not tamper with appliance components.
6. REFERENCE STANDARDS AND LAWS
Install the appliance in compliance with current safety regula-
tions.
Install the appliance in compliance with current regulations.
7. HANDLING
• The packaging is marked with warning symbols that indicate
the precautions to be taken when handling the appliance
to avoid damage.The appliance must only be handledus-
ing suitable equipment. If lifting equipment is used, such as
forklift trucks or similar, make sure that the appliance is in a
stable position .
8. UNPACKING
Check the state of the packaging and in the event of damage,
ask the delivery person to inspect the goods.
• Remove the packaging.
• Remove the protective
fi lm from the exterior and interior pan-
els. Use a suitable solvent to remove any residual adhesive
from the panels.
9. POSITIONING
• The overall dimensions of the appliance and the position of
connections are given on the installation diagram at the start
of this manual.
• The appliance can be installed singly or in combination with
other appliances in the same product range.
• The appliance is not suitable for integrated installation.
• Position the appliance at least 10 cm from adjacent walls.
This distance can be reduced in the presence of non-com-
bustible walls or heat-insulated walls.
• Level the appliance by means of the height-adjustable feet.
APPLIANCE ASSEMBLY WITH BASE
Follow the instructions provided with the type of support uti-
lized.
JOINING APPLIANCES TOGETHER IN LINE
• Place the appliances side by side and adjust the tops to the
same height.
• Unite the appliances using the special unionjointcoverings
supplied upon request