background image

Warranty Message

The product you have purchased comes with a 

limited warranty

 from Mercury Marine; the terms of the warranty are set forth

in the Warranty Manual included with the product. The Warranty Manual contains a description of what is covered, what is not

covered, the duration of coverage, how to best obtain warranty coverage, 

important disclaimers and limitations of

damages

, and other related information. Please review this important information.

Copyright and Trademark Information

© MERCURY MARINE. All rights reserved. Reproduction in whole or in part without permission is prohibited.

Alpha, Axius, Bravo One, Bravo Two, Bravo Three, Circle M with Waves Logo, K‑planes, Mariner, MerCathode, MerCruiser,

Mercury, Mercury with Waves Logo, Mercury Marine, Mercury Precision Parts, Mercury Propellers, Mercury Racing,

MotorGuide, OptiMax, Quicksilver, SeaCore, Skyhook, SmartCraft, Sport‑Jet, Verado, VesselView, Zero Effort, Zeus, #1 On the

Water and We're Driven to Win are registered trademarks of Brunswick Corporation. Pro XS is a trademark of Brunswick

Corporation. Mercury Product Protection is a registered service mark of Brunswick Corporation.

Identification Records

Please record the following applicable information:

MerCruiser

Engine Model and Horsepower

Engine Serial Number

   

Transom Assembly Serial Number (Sterndrive)

Gear Ratio

Sterndrive Unit Serial Number

   

Transmission Model (Inboard)

Gear Ratio

Transmission Serial Number

   

Propeller Number

Pitch

Diameter

   

Hull Identification Number (HIN)

Purchase Date

   

Boat Manufacturer

Boat Model

Length

   

Exhaust Gas Emissions Certification Number (Europe Only)

   

Содержание TDI 4.2L


























































































Отзывы: