Mercury TDI 4.2L Скачать руководство пользователя

Страница: 69 / 89

Section 4 - Maintenance

90-8M0114081

eng

DECEMBER 2015

Page 63

8. Install the propeller shaft anode and secure with the screw. Tighten the screw to the specified torque.

Bravo Three

a -

Rear propeller nut

b -

Rear propeller

c -

Rear propeller thrust hub

d -

Front propeller nut

e -

Front propeller

f -

Front propeller thrust hub

g -

Propeller shaft anode screw

h -

Flat washer

i -

Star washer

j -

Propeller shaft anode

Description

lb‑in.

lb‑ft

Propeller shaft anode screw

168

–

Drive Belts

Drive Belt

All drive belts must be periodically inspected for tension and condition. Turn the engine off and remove the ignition key before

inspecting for excessive wear, cracks, fraying, and glazed surfaces.

WARNING

Inspecting the belts with the engine running may cause serious injury or death. Turn off the engine and remove the ignition

key before inspecting the belts.

In the event that the drive belt requires replacement, it is recommended that the drive belt replacement be performed by a

Mercury Diesel–authorized repair facility.

Drive Belt Failure Identification

Appearance

Description

Cause

Solution

40791

Abrasion

Each side of the belt appears

shiny or glazed. Severe

condition: Fabric is exposed.

The belt is in contact with an object.

This can be caused by improper

belt tension or tensioner failure.

Replace the belt and

inspect its route for

contact with another

object. Verify that the belt

tensioner is functioning.

40794

Pilling

Belt material is sheared off from

the ribs and builds up in the belt

grooves.

There are a number of causes

including lack of tension,

misalignment, worn pulleys, or a

combination of these factors.

When pilling leads to belt

noise or excess vibration,

the belt should be

replaced.

5304

g h

Содержание TDI 4.2L


























































































Результаты поиска

Содержание TDI 4.2L

Отзывы:

Похожие инструкции для TDI 4.2L

Бренды по названию

Популярные бренды

Mercury TDI 4.2L, Руководство пользователя

Результаты поиска

Содержание TDI 4.2L

Отзывы:

Похожие инструкции для TDI 4.2L

Бренды по названию

Популярные бренды