Mercury MerCruiser Series, Руководство пользователя

Страница: 84 / 101

5. Start the engine and operate until it reaches normal operating temperature.
6. Stop the engine.
7. Drain the engine oil and install a new oil filter.
8. Fill the crankcase with a high‑quality diesel engine compatible protective oil such as Tectyl™ 915W40 up to the minimum
level indicated on the dipstick.
9. Flush the seawater cooling system. Refer to
Section 5
‑
Flushing the Seawater System
.
10. Check for oil leaks.
11. Drain the seawater system and protect it with propylene glycol antifreeze. Refer to
Section 5
‑
Draining and Protecting
the Seawater System.
NOTE: Before starting the engine to draw in the propylene glycol antifreeze, remove the air filter. Restart the engine and
spray a small amount of Storage Seal Rust Inhibitor into the intake pipe.
IMPORTANT: An excessive amount of Storage Seal is not required, the intention is to coat the compressor portion of the
turbocharger only, and not the engine combustion chambers. Never introduce an excessive amount of oil to the intake of a
diesel engine.
Tube Ref No. Description Where Used Part No.
119
Storage Seal Rust Inhibitor Turbocharger inlet vanes 92-858081K03
12. Immediately stop the engine when the antifreeze has been drawn into the engine. Install the air filter.
13. Drain all residual protective oil from the engine.
14. Replace the engine oil filter with a new one.
15. Relieve the tension from the serpentine belt, or remove the belt completely.
16. Remove the seawater pump impeller and store away from direct sunlight.
IMPORTANT: Place a caution tag at the instrument panel and in the engine compartment stating to not operate the engine,
as the seawater pump impeller is out, the belt is removed, and the sump is void of oil.
Battery
Follow the battery manufacturer's instructions for storage.
Recommissioning
NOTE: Discharge of propylene glycol into the environment may be restricted by law. Contain and dispose of propylene glycol in
accordance with federal, state, and local laws and guidelines.
1. On engines prepared for extended storage, have a Mercury Diesel authorized repair facility install the seawater pump
impeller, if it was removed for storage.
2. Replace the serpentine belt, if it was removed for storage. Refer to
Section 5
‑
Drive Belt
.
3. On engines that were prepared for cold weather (freezing temperature), seasonal, or extended storage, refer to
Section 5
‑
Draining and Protecting the Seawater System
and drain the propylene glycol into a suitable container. Dispose of the
propylene glycol in accordance with federal, state, and local laws and guidelines.
4. Ensure that all cooling system hoses are in good condition, connected properly, and clamped tightly. Verify that all drain
valves and drain plugs are installed and tight.
5. Inspect all drive belts.
6. Fill the engine with oil. Refer to
Section 5
‑
Engine Oil
.
7. Perform all lubrication and maintenance specified for completion according to
Section 5
‑
Maintenance Schedules
,
except items that were performed at time of engine service.
8. Fill the fuel tanks with fresh diesel fuel. Do not use old fuel. Check the general condition of the fuel lines and inspect the
connections for leaks.
9. Replace the fuel filters.
!
CAUTION
Disconnecting or connecting the battery cables in the incorrect order can cause injury from electrical shock or can damage
the electrical system. Always disconnect the negative (‑) battery cable first and connect it last.
10. Install a fully charged battery. Clean the battery cable clamps and terminals. Reconnect the cables (refer to the CAUTION
listed above). Secure each cable clamp when connecting. Coat terminals with a battery terminal anti‑corrosion spray to
help retard corrosion.
11. Perform all checks in the Starting Procedure column found in the
Operation Chart
. Refer to
Section 3
‑
On the Water
.
Section 6 - Storage
Page 78 90-8M0117076
eng
FEBRUARY 2018