Mercury MerCruiser 4.3 TKS Скачать руководство пользователя

Страница: 94 / 122

Section 6 - Storage

Page 86

90-899883179 OCTOBER 2007

Cold Weather or Extended Storage

IMPORTANT: Mercury MerCruiser strongly recommends that this service should be

performed by an authorized Mercury MerCruiser dealer. Damage caused by freezing

temperatures IS NOT covered by the Mercury MerCruiser Limited Warranty.

NOTICE

Water trapped in the seawater section of the cooling system can cause corrosion or

freeze damage. Drain the seawater section of the cooling system immediately after

operation or before any length of storage in cold weather. If the boat is in the water, keep

the seacock closed until restarting the engine to prevent water from flowing back into the

cooling system. If the boat is not fitted with a seacock, leave the water inlet hose

disconnected and plugged.

NOTE: As a precautionary measure, attach a tag to the key switch or steering wheel of the

boat reminding the operator to open the seacock or unplug and reconnect the water inlet

hose before starting the engine.

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the

manufacturers instructions, be used in the seawater section of the cooling system for

freezing temperatures or extended storage. Make sure that the propylene glycol antifreeze

contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow

the propylene glycol manufacturer's recommendations.

Preparing Power Package for Storage

1. Fill the fuel tanks with fresh gasoline (that does not contain alcohol) and a sufficient

amount of Quicksilver Gasoline Stabilizer for Marine Engines to treat the gasoline.

Follow instructions on the container.

2. If the boat is to be placed in storage with fuel containing alcohol in fuel tanks (if fuel

without alcohol is not available): Fuel tanks should be drained as low as possible and

Mercury/Quicksilver Gasoline Stabilizer for Marine Engines added to any fuel

remaining in the tank. Refer to

Fuel Requirements

for additional information.

3. Flush the cooling system. Refer to the

Maintenance

section.

IMPORTANT: In order to run the engine as required in the remainder of the storage

preparation procedure, water must be supplied to the engine as described in the flushing

procedure.
4. Provide cooling water to the engine as done in the previous step.
5. Operate the engine sufficiently to bring it up to normal operating temperature and allow

fuel with Mercury/Quicksilver Gasoline Stabilizer to circulate through the fuel system.

Shut off the engine.

6. Change the oil and oil filter.
7. Prepare the engine and fuel system for storage. Refer to

Engine and Fuel System

Preparation

8. Drain the engine seawater cooling system. Refer to

Draining the Seawater System

Содержание MerCruiser 4.3 TKS



























































































































Результаты поиска

Содержание MerCruiser 4.3 TKS

Отзывы:

Похожие инструкции для MerCruiser 4.3 TKS

Бренды по названию

Популярные бренды

Mercury MerCruiser 4.3 TKS, Руководство пользователя

Результаты поиска

Содержание MerCruiser 4.3 TKS

Отзывы:

Похожие инструкции для MerCruiser 4.3 TKS

Бренды по названию

Популярные бренды