Mercury MerCruiser 4.3 TKS Скачать руководство пользователя

Страница: 73 / 122

Section 5 - Maintenance

90-899883179 OCTOBER 2007

Page 65

Propellers

Propeller Repair

Some damaged propellers can be repaired. Contact your authorized Mercury MerCruiser

dealer.

Alpha Propeller Removal

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the

water with a propeller installed. Before installing or removing a propeller, place the drive

unit in neutral and engage the lanyard stop switch to prevent the engine from starting.

Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Place wood block between propeller blade and anti‑ventilation plate to prevent rotation.

Straighten bent tabs on tab washer.

2. Turn propeller shaft nut counterclockwise to remove nut.
3. Slide tab washer, drive sleeve, propeller and thrust hub off propeller shaft.

Alpha Propeller Installation

NOTICE

Operating the engine with a loose propeller can damage the propeller, the drive, or drive

components. Always tighten the propeller nut or nuts to specification and check for

tightness periodically and at the required maintenance interval.

IMPORTANT: If reusing tab washer, carefully inspect tabs for cracks or other damage.

Replace tab washer if condition is questionable.

6215

a -

Propeller shaft

b -

Thrust hub

c -

Flo‑Torq II drive hub

d -

Propeller

e -

Drive sleeve

f -

Locking tab washer

g -

Propeller nut

1. Apply a liberal coat of one of the following lubricants to the propeller shaft.

Tube Ref No.

Description

Where Used

Part No.

Special Lubricant 101

Propeller shaft

92-802865Q02

Содержание MerCruiser 4.3 TKS



























































































































Результаты поиска

Содержание MerCruiser 4.3 TKS

Отзывы:

Похожие инструкции для MerCruiser 4.3 TKS

Бренды по названию

Популярные бренды

Mercury MerCruiser 4.3 TKS, Руководство пользователя

Результаты поиска

Содержание MerCruiser 4.3 TKS

Отзывы:

Похожие инструкции для MerCruiser 4.3 TKS

Бренды по названию

Популярные бренды