Mercury MerCruiser 4.3 TKS Скачать руководство пользователя

Страница: 62 / 122

Section 5 - Maintenance

Page 54

90-899883179 OCTOBER 2007

1. Check the gear lube oil level. Keep the oil level within the recommended operating

range. If any water is visible at the bottom of the monitor or appears at the oil fill/drain

plug and/or if oil appears discolored, contact your authorized Mercury MerCruiser

dealer immediately. Both conditions may indicate a water leak somewhere in the

sterndrive unit.

6107

6105

Seawater cooled models

Closed cooled models

a -

Gear lube monitor

Filling

IMPORTANT: If more than 59 mL (2 fl oz) of High Performance Gear Lubricant is required

to fill the monitor, a seal may be leaking. Damage to the sterndrive unit may occur due to

lack of lubrication. Contact your authorized Mercury MerCruiser dealer.
1. Remove the gear lube monitor cap.
2. Fill the monitor with the specified fluid so that the oil level is in the operating range. Do

not overfill.

Tube Ref No.

Description

Where Used

Part No.

High Performance Gear

Lubricant

Gear lube monitor

92-858064K01

3. Replace the cap.

NOTE: When filling the entire sterndrive unit refer to Changing.

Содержание MerCruiser 4.3 TKS



























































































































Результаты поиска

Содержание MerCruiser 4.3 TKS

Отзывы:

Похожие инструкции для MerCruiser 4.3 TKS

Бренды по названию

Популярные бренды

Mercury MerCruiser 4.3 TKS, Руководство пользователя

Результаты поиска

Содержание MerCruiser 4.3 TKS

Отзывы:

Похожие инструкции для MerCruiser 4.3 TKS

Бренды по названию

Популярные бренды