Mercury 1.7 MI Скачать руководство пользователя

Страница: 36 / 248

ON THE WATER

SECTION 3

Page 28

CMD-3967823 / 90-865237030 OCTOBER 2003

CE481

STARTING COLD ENGINE

IMPORTANT: Check fluid levels before starting engine. Refer to Maintenance

Schedule.

1. Turn on and operate the engine compartment bilge blower (if equipped) for five minutes.

Or, open engine hatch to air out bilge before attempting to start engine.

2. Place control handle in NEUTRAL.
3. If engine has not been run for a period of time and will not readily start with the standard

starting procedure, there is a hand pump/primer located on the engine to improve initial

fuel supply. Refer to Maintenance - Fuel System, Priming Fuel System and follow

instructions.

4. Follow the appropriate starting procedure a. or b.:

Indicator lamp models:

turn the key switch to the RUN position to activate the glow

plugs. The preheat cycle usually lasts 10 to 15 seconds. Observe the preheat

indicator (glow plug) lamp. The lamp should be illuminated when the engine cylinder

temperature is too low to sustain combustion. The engine should be started only

after the lamp goes off.

NOTE:

The preheat devices (glow plugs) should operate at temperatures lower than 50

degrees C (122 degrees F). An engine coolant temperature sensor will automatically control

activation and duration of preheat cycle.

Wait to start models:

turn the key switch to the RUN position to activate the glow

plugs. Wait five seconds for the preheat cycle. The engine should be started only

after the five second wait to start period has ended.

NOTE:

The preheat devices (glow plugs) should operate at temperatures lower than 80

degrees C (176 degrees F). An engine coolant temperature sensor will automatically control

activation and duration of preheat cycle.

IMPORTANT: After starting, the key switch should NOT be returned to the OFF

position during engine operation. If the starter switch is in the OFF position and the

engine is operating, the battery will not be charged, audio warning alarms will not be

operational in the event of trouble and accessories may not operate.

5. Turn key switch to START position. Release key when the engine starts. Allow switch

to return to RUN position. Do not operate the engine with the switch in the OFF position

without first shutting down the engine, using the engine stop switch.

CAUTION

Do not attempt to engage the starter while the engine is running as this will lead to

starter pinion and ring gear damage.

6. Ensure all instrumentation is functioning properly and indicating normal readings.

Ensure charge indicator and oil pressure warning lamps go off. Check oil pressure

gauge immediately after engine starts. If oil pressure is not within specified range (refer

to Specifications), stop the engine, locate and correct the problem, or see your local

auathorized Cummins MerCruiser Diesel dealer / distributor if you are unable to

determine the problem.

CAUTION

Do not increase the engine speed until the oil pressure gauge indicates normal.

Shut the engine down if oil pressure does not register on the gauge within 20 to 30

seconds after start.

INDEX

Содержание 1.7 MI

























































































































































































































































Результаты поиска

Содержание 1.7 MI

Отзывы:

Похожие инструкции для 1.7 MI

Бренды по названию

Популярные бренды

Mercury 1.7 MI, Руководство пользователя

Результаты поиска

Содержание 1.7 MI

Отзывы:

Похожие инструкции для 1.7 MI

Бренды по названию

Популярные бренды