Mendota ML54 страница 75 Скачать руководство пользователя

Страница: 75 / 96

85-03-01145

ML54

Page

6.5

REMOTE CONTROL OPERATING INSTRUCTIONS

To Turn on the Fireplace

NOTE: If the fireplace does not respond to the remote-

control commands, the fireplace system may have entered “safety

lockout” mode. To reset the system, see

Chapter 6.11.12 Why won’t my fireplace turn on?

Press the on/off button. The remote-control display will show all active icons on the screen and the fireplace will emit an
audible beep.

Select the thermostat mode by pressing the thermostat button: OFF (meaning Manual), ON (meaning Normal
Thermostat) or Smart (meaning Smart Thermostat).

If the thermostat icon displays as “

OFF

”

(Manual), the fireplace will ignite and start on Hi.

If the thermostat icon displays as “ON” (Normal Thermostat

), the fireplace will only ignite if the thermostat

temperature is greater than the room temperature.

If the thermostat icon displays as “

SMART

” (Smart Thermost

at), the fireplace will only ignite if the

thermostat temperature is greater than the room temperature.

To Turn off the Fireplace

Press the on/off button. The fireplace will turn off.

Understanding Your Remote-Control Icons

Your remote control displays and controls the following functions. See below for detailed control explanations.

Note: the “AUX On” and “Rear Burner”

functions are not used in this fireplace.

Figure 6-2 Remote Control Icons

Содержание ML54

































































































Результаты поиска

Содержание ML54

Отзывы:

Похожие инструкции для ML54

Бренды по названию

Популярные бренды

Mendota ML54, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ML54

Отзывы:

Похожие инструкции для ML54

Бренды по названию

Популярные бренды