Mendota ML54 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 96

background image

85-03-01145

ML54

Page

6

GENERAL INFORMATION

3.1

SAFETY AND WARNING INFORMATION

Building Permit & Inspection Requirements

All installations of Mendota Fireplaces must comply with all the requirements stated in this Installation and Operating Manual.
The dealer and/or installer must obtain all required building permits and inspection approvals from the local building inspection
department or the local jurisdiction. To validate warranty coverage, Mendota may require facsimile copies of the building
permit and inspection approval forms. Failure to provide adequate proof that the installation conforms to all local requirements
and the requirements stated in the Installation and User Manual will void all applicable warranties.

Other Cautions

CAUTION

: Each installation must conform to all local, state and national codes. Refer to the national fuel

gas code and local zoning and code authorities for details on installation requirements. The Mendota
Fireplace must be vented to the outside in accordance with the latest edition of the National Fuel Gas Code.
In the absence of local codes, the insta llation must conform to the most current edition of the National Fuel
Gas Code AN SI Z223.1, also known as NFPA 54.

CAUTION

: The Mendota Fireplace may be installed in a manufactured (mobile) home after the first sale of

the home. Manufactured home (mobile home) installation must conform with the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the
Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A, or CSA Z240.4 -Gas Equipped Mobile
Housing. Consult your local building official. NOTE: For mobile home installations, unit must be bolted to
the Woodburning fireplace firebox floor and properly grounded.

INSTALLER

: Leave this manual with the appliance.

CONSUME

R: Retain this manual for future reference.

INSTALLATEUR

: Laissez cette notice avec l’appareil.

CONSOMMATEUR

: Conservez cette notice pour

consultation ultérieure.

«
...
4
5
6
7
8
...
»

Содержание ML54

































































































Отзывы:

Нет отзывов

Похожие инструкции для ML54

Бренд: Pacific energy Страницы: 24

Бренд: barkman Страницы: 16

Бренд: Dimplex Страницы: 63

Бренд: Napoleon Страницы: 144

Бренд: Bold Flame Страницы: 20

Бренд: Evonicfires Страницы: 29

Бренд: Harman Страницы: 28

Бренд: Heat-N-Glo Страницы: 37

CORINTHIA BLACK NG

Бренд: superior fires Страницы: 12

Inglenook IWZC-02

Бренд: Country Flame Страницы: 54

Wellington Surround

Бренд: Valor Fires Страницы: 8

Бренд: Heat & Glo Страницы: 49

Бренд: Monessen Hearth Страницы: 32

Бренд: Bluegrass Living Страницы: 8

Бренд: HEAT GLO Страницы: 48

Бренд: Cannon Страницы: 20

Бренд: Uberhaus Страницы: 7

Бренд: Napoleon Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды