Mendota ML54 страница 1 Скачать руководство пользователя | Manualshive

Страница: 1 / 96

background image

85-03-01145-D

ML54

Installation and Operating Instructions

MODEL NO. ML54 FULLVIEW DIRECT VENT GAS FIREPLACE HEATER

WARNING:

If the information in these instructions

is not followed exactly, a fire or explosion may
result causing property damage, personal injury or
loss of life.

AVERTISSEMENT

. Assurez-vous de bien suivre les

instructions données dans cette notice pour réduire au
minimum le risque d'incendie ou d'explosion ou pour
éviter tout dommage matériel, toute blessure ou la mort.

- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not
use any phone in your building.

•

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call
the fire department.

- Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.

Ne pas entreposer ni utiliser d'essence ni d'autres vapeurs
ou liquids inflammables dans le voisinage de cet appareil
ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d'allumer d'appareil.

• Ne touchez à aucun interrupteur. Ne pas vous servir des

téléphones se trouvant dans le bâtiment où vous trouvez.

• Appelez immédiatement votre fournisseur de gaz depuis

un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incendies.
- L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par le
fournisseur de gaz.

This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local
codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gasses, unless a
certified kit is used.

Cet appareil peut être installé dans une maison
préfabriquée (É.-U. seulement) ou mobile déjà installée à
demeure si les règlements locaux le permettent.
Cet appareil doit être utilisé uniquement avec les types de
gaz indiqués sur la plaque signalétique. Une trousse de
conversion est fournie avec cet appareil.

A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and must be installed.

Une barrière conçue pour réduire le risque de brûlures
du verre chaud est fournie avec cet appareil et doit être
installée.

1
2
3
...
»

Содержание ML54

































































































Отзывы:

Нет отзывов

Похожие инструкции для ML54

Бренд: Harrie Leenders Страницы: 26

MTVERNINSAE-MBK

Бренд: Quadra-Fire Страницы: 24

Бренд: Rinnai Страницы: 32

Purefire Panoramic 5kw Slimline - SE

Бренд: Ecosy+ Страницы: 12

Бренд: HAMPTON BAY Страницы: 8

Бренд: Mendota Страницы: 80

Бренд: Napoleon Страницы: 2

Бренд: Desa Страницы: 32

Бренд: Travis Industries Страницы: 9

Бренд: Napoleon Страницы: 8

Luna Gold Series

Бренд: M Design Страницы: 14

Бренд: barbas Страницы: 44

Бренд: Vanguard Страницы: 40

Haliburton GDS28P

Бренд: Napoleon Страницы: 48

Бренд: Majestic Страницы: 36

Бренд: Superior Страницы: 24

Бренд: glamour Страницы: 12

Бренд: Pur Line Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды