manualshive.com logo in svg

Memotec NetPerformer SDM-9120 Series, Руководство по установке оборудования

Поделиться
Скачать
Memotec NetPerformer SDM-9120 Series Скачать руководство пользователя страница 89

 

  Product Description

Memotec Inc. 

4-21

4.11 DSP Resources

High density, high performance DSP processors digitize, process and compress voice 
signals on the NetPerformer unit. The DSP processors handle voice compression 
software and fax/modem emulation.

4.11.1

DSP-160 Module for SDM-9120/9220/9230

A single low-density module (DSP-160) has 1, 2, 3, 5 or 6 DSP processors. Each DSP 
processor supports 5 digital timeslots. Maximum 30 voice channels per DSP module.

NOTE:

One low-density onboard DSP processor is provided with each FXS, FXO and 

E&M interface card to support analog voice calls. A maximum of 8 analog voice 
channels is permitted.

NOTE:

If you require support of more than 30 voice channels, upgrade to the high-

density DSP module (HD-DSP).

Figure 4-15:   DSP-160 Module

Caution

The low-density DSP module is intended for the SDM-9120, SDM-9220 
and SDM-9230 only. 

DO NOT replace the low-density DSP module 

with a DSP intended for legacy NetPerformer products (SDM-9360, 
SDM-9380 and SDM-9585).

Notched edge

Содержание NetPerformer SDM-9120 Series


































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды