Memotec NetPerformer SDM-9120 Series Скачать руководство пользователя страница 28

Страница: 28 / 161

NetPerformer Hardware Installation Guide

2-6

Memotec Inc.

One RJ-11 to RJ-11 cable for each FXS or FXO port

One RJ-45 to RJ-45 cable for each E&M/PTT port

•

All user equipment that will be directly connected to the serial ports.

•

A sufficient number of ferrites for the cables connecting to the ports on the unit.
For details, see

“Installing the Ferrites (EMI Filters)” on page 3-27

for the ferrites

required on the different product models for the various types of ports, the
countries where these ferrites are required, and installation instructions.

NOTE:

These ferrites are not provided with the product package.

Содержание NetPerformer SDM-9120 Series


































































































































































Результаты поиска

Содержание NetPerformer SDM-9120 Series

Отзывы:

Бренды по названию

Популярные бренды

Memotec NetPerformer SDM-9120 Series, Руководство по установке оборудования

Результаты поиска

Содержание NetPerformer SDM-9120 Series

Отзывы:

Бренды по названию

Популярные бренды