Memotec NetPerformer SDM-9120 Series Скачать руководство пользователя страница 47

Страница: 47 / 161

Hardware Installation

Memotec Inc.

3-19

Reinstall the faceplate of the bottom interface card slot.

Reinsert the bottom interface card into the card slot.

►

Sliding an FXS or E&M card in the BOTTOM interface card slot of an

SDM-9140 Series unit:

If the top interface card slot is empty, remove the metal faceplate.

If the top interface card slot contains a card, remove the card from the
top interface card slot.

Position the bottom interface card

at a slight angle

in front of the card

slot.

Slowly slide the card into the side rails of the slot, making sure the

components on the bottom of the card do not touch the base of the
chassis.

Continue to insert the card until it is fully inserted.

Reinstall the faceplate on the top interface card slot.

Reinsert the top interface card into the card slot.

IMPORTANT

: When reinserting the top interface card, make sure that the

solder side (bottom) of the top card does not interfere with the component
side (top) of the bottom card.

Figure 3-11: Positioning an FXS/E&M Card at an Angle to an SDM-9140 Slot

Position the FXS or E&M card

at an angle to the card slot

Plastic card rails

Содержание NetPerformer SDM-9120 Series


































































































































































Результаты поиска

Содержание NetPerformer SDM-9120 Series

Отзывы:

Бренды по названию

Популярные бренды

Memotec NetPerformer SDM-9120 Series, Руководство по установке оборудования

Результаты поиска

Содержание NetPerformer SDM-9120 Series

Отзывы:

Бренды по названию

Популярные бренды