background image

6.  If burner does not ignite using igniter, see “Match Lighting the Main 

Burners” section. 

7.  To turn off, turn each control knob clockwise until it locks in the “OFF” position. This does not turn off

the gas fl ow from the cylinder. 

 

Note:  If burner does not light or fl ame is too low, See “Trouble Shooting” section of the owners manual. 

WARNING

9

LIGHTING THE MAIN BURNERS:

1.  Open lid before lighting burner.

2.  Make sure all control knobs are “OFF”.

3.  Select burner to be lit. Push and turn control knob to “HIGH”.   Press igniter 

for 3-5 seconds. 

4.  If ignition does NOT occur in 5 seconds, turn control knob to “OFF”, 

wait 5 minutes to allow gas to dissipate and repeat lighting procedure.

5.  To light other burners, follow steps 3-4.

DANGER

Property damage, bodily harm, severe burns, and death could result from failure to follow these 
safety steps. These steps should be performed after the grill has been assembled and prior to 
each use. DO NOT operate this grill until you have read and understand ALL of the warnings and 
instructions in this manual.

• 

Ensure that the grill is properly assembled.

• 

Inspect gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is evident 
there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to grill being used. 
Replace with hose and regulator Model No. 9670-155-9670-0, which can be obtained by contacting 
customer service at 855-735-9922.

• 

Leak check all gas connections, hose and propane tank. See section on “Leak Testing”.

• 

Position your grill on a non-combustible level surface in a well ventilated location, a safe distance
10 ft. (3.1 m) from combustible materials, buildings and overhangs.

• 

Properly place empty grease cup under grease drain hole in bottom of grill to catch grease during use.

• 

DO NOT block ventilation areas in sides, back or cart compartment of grill.

PRE-START CHECK LIST:

LIGHTING INSTRUCTIONS:

Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any 
of the warnings and instructions contained in the preceding sections of this manual. 

Follow the instructions exactly.

1.  OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside 

the grill. An explosion could occur if grill lid is down.

2.  Check that all burner control knobs and the cylinder valve are turned to the “OFF” position.

3.  Turn on the fuel supply by slowly rotating the cylinder valve knob counter-clockwise to full open.

4.  DO NOT stand with head, body, or arms over the grill when lighting.

OFF

HIGH

IGNITER

Содержание GAS9670AS


































Отзывы: