background image

16

TROUBLE SHOOTING:

Problem

Possible Cause

Prevention/Cure

Burner will not light

LP gas tank valve is closed

Make sure regulator is securely attached to the LP gas tank, turn LP 
gas tank valve to “OPEN”

LP gas tank is low or empty

Check if LP gas tank is empty. If empty, replace or refi ll.

LP gas leak

1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Leak Testing” in the owner’s manual

Coupling nut and regulator not fully connected

See section on “Connecting Hose and Regulator”

Obstruction of gas fl ow

1. Clean burner assembly
2. Check for bent or kinked hose

Burner may not be properly seated

Reseat burner and valve. Refer to “Burner Assembly/Maintenance” 
instructions

Spider webs or insect nest in venturi

Clean venturi and burner assembly

Burner ports clogged or blocked

Clean burner ports

Battery needs to be changed

Replace the battery (follow assembly step for inserting battery)

Wires or electrode covered with cooking residue

Clean wire and/or electrode with rubbing alcohol

Electrode and burners are wet

Wipe dry with cloth

Electrode cracked or broken - sparks at crack

Replace electrode

Wire loose or disconnected

Reconnect wire or replace electrode/wire assembly

Wire is shorting (sparking) between ignitor and 
electrode

Replace ignitor wire/electrode assembly

Bad ignitor

Replace ignitor

Grill does not get hot 
enough

Out of gas

Replace or refi ll LP gas tank

Flow limiting device may have been activated

1. Mini Reset:
    a. Turn control knobs and LP gas tank valve to “OFF” 
    b. Wait one minute and relight grill per “Lighting Instructions”
2. If fl ames are still too low, perform a Full Reset
    Full Reset:
    a. Turn control knobs and LP gas tank valve to “OFF”   
    b. Disconnect regulator from propane tank
    c. Inspect LP cylinder rubber seal
    d. Wait 1 minute
    e. Reconnect regulator and perform “Leak Testing” on all 

    connections.

    f. Light grill per “Lighting Instructions”

Irregular fl ame pattern. 
Flame does not run full 
length of burner

Burner ports are clogged or blocked

Air shutter on burner needs adjustment

Clean burner ports

See section on “Burner Adjustment”

Flame is yellow or orange

New burner may have residual manufacturing 
oils

Burn grill for 15 minutes on “HIGH” with the lid closed

Spider webs or insect nest in venturi

Clean venturi and burner assembly

Food residue, grease, etc.

Clean burner assembly

Poor alignment of valve to burner venturi

Air shutter on burner needs adjustment

Make sure burner venturi is properly engaged with valve

See section on “Burner Adjustment”

Содержание GAS9670AS


































Отзывы: