Meltem M-WRG-II Скачать руководство пользователя страница 40

Страница: 40 / 48

Installation manual

M-WRG-II ventilation units

- 40 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

11.7

Connecting the mains cable and control cable (if used)

DANGER

Potentially fatal voltages

—

The electrical installation work must only be carried out by a qualified electrician.

— The VDE regulations or any special safety regulations applicable in your country

apply to the electrical installation work.

►

Before starting installation or maintenance work, disconnect the mains cable for

connecting to the ventilation unit on all poles from the mains supply.

► Observe the five safety rules (DIN VDE 0105-100, EN 50110-1) for working on elec

trical systems:

— Disconnect from mains (all-pole disconnection of a system from live parts)

— Secure against reconnection

— Check that the system is voltage-free

— Earth and short-circuit

— Cover or block off access to adjacent live parts

NOTICE

— The ventilation unit may be

damaged if the mains or control

cable is connected incorrectly. This

will also invalidate the warranty.

— No protective earth (PE) conductor

is required.

►

Connect the neutral conductor N

(item N in Fig. 47) and the outer

conductor L (item L in Fig. 47) to the

connector (item 1 in Fig. 47) in the

ventilation unit.

►

If used, connect the wire for the

external control input (item S in

Fig. 47) to the connector.

►

If used, connect the control cable to

the terminal block (item 2 in Fig. 47)

on the connection board (only on

certain ventilation units, see Table 4

in section 10.9 on page 29).

NOTICE

Connection of the control cable is

described in separate installation

manuals.

Fig. 47: Connecting the mains cable and control cable

(if used)

Содержание M-WRG-II

















































Результаты поиска

Содержание M-WRG-II

Отзывы:

Похожие инструкции для M-WRG-II

Бренды по названию

Популярные бренды

Meltem M-WRG-II, Руководство по установке

Результаты поиска

Содержание M-WRG-II

Отзывы:

Похожие инструкции для M-WRG-II

Бренды по названию

Популярные бренды