Meltem M-WRG-II Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 48

background image

Installation manual

M-WRG-II ventilation units

- 14 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

3.1.4 Electrical connection

The working voltage range of the ventilation unit is between 85 V AC and 265 V AC /

50-60 Hz.

NOTICE

If the ventilation unit is not equipped with a mains connection cable and plug or other

means of disconnecting from the mains supply that has, at each pole, a contact opening

width that conforms to the conditions of overvoltage category III for complete separa-

tion, then such an isolating unit (e.g. circuit breaker) must be integrated into the perma-

nently installed electrical system in accordance with the installation regulations. The

isolating unit must be identified as such and easy to access.

3.2

Flush-mount installation

An M-WRG-II flush-mount installation kit is needed to flush-mount the ventilation unit

(optionally with ductwork connection).

►

Also read and follow the “Planning notes” section of the installation manual that is

supplied with the flush-mount installation kit (see section “1.11 Supplementary docu

ments” on page 8).

3.3

U

2

integrated into wall installation

An M-WRG-II U

2

installation kit is needed to integrate the ventilation unit into the wall.

►

Also read and follow the “Planning notes” section of the installation manual that is

supplied with the integrated into wall installation kit (see section “1.11 Supplementary

documents” on page 8).

«
...
12
13
14
15
16
...
»

Содержание M-WRG-II

















































Отзывы:

Нет отзывов

Похожие инструкции для M-WRG-II

Бренд: ABB Страницы: 52

Бренд: ABB Страницы: 63

Бренд: EA Страницы: 24

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Бренд: B&R Industries Страницы: 89

Бренд: C3 Custom Coolers Страницы: 16

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Harsco Industrial Страницы: 57

Бренд: Lamtec Страницы: 136

Бренд: Xilinx Страницы: 2

Бренд: National Instruments Страницы: 78

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

Бренд: Absima Страницы: 5

Бренд: Beckhoff Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды