manualshive.com logo in svg

Meltem M-WRG-II, Руководство по установке

Поделиться
Скачать
Meltem M-WRG-II Скачать руководство пользователя страница 33

Installation manual 

M-WRG-II ventilation units

- 33 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION  THE  RIGHT WAY

V E N T I L A T I O N   &   H E A T   R E C O V E R Y

10.12  Sealing ventilation pipes on external wall

NOTICE

If the external plaster encloses the 

ventilation pipes all round and without 

gaps, you can skip the steps described 

in this section.

 

►

Chamfer both pipe breakthrough 

edges (item 1 in Fig. 20) to roughly 

5x45° to create enough space for the 

sealing joints with permanently elastic 

sealant.

 

►

Fill the chamfers of the pipe break-

through edges all-round with perma-

nently elastic sealant on the outside.

NOTICE

Only use a solvent-free sealant if the sealant is applied to polystyrene.

10.13  Attaching the outer wall terminal

 WARNING

Do not run without the outer wall 

terminal

Please note that the ventilation unit 

must not be used without the outer 

wall terminal for safety reasons.

 

►

Attach the outer wall terminal to the 

external wall.

NOTICE

Installation of the outer wall terminal 

is described in a separate installation 

manual (see “1.11 Supplementary 

documents” on page 8).

Fig. 30:  Sealing ventilation pipes on external wall

1

Fig. 31:  Attaching the outer wall terminal

Содержание M-WRG-II

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды