Meltem M-WRG-II Скачать руководство пользователя страница 35

Страница: 35 / 48

Installation manual

M-WRG-II ventilation units

- 35 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

11.3

Checking the air flap on the exhaust air spigot and seals

► Check that the air flap (item 1 in

Fig. 34) on the exhaust air spigot is

correctly seated in the holder (item 2

in Fig. 34).

►

Check that the seals (item 3 in

Fig. 34) around the air spigots on

the back of the ventilation unit are

undamaged. Damaged seals should

be replaced immediately.

NOTICE

— The ventilation unit will not operate

perfectly unless the air flap is

seated correctly.

— For ease of installing the unit (see

section 11.6 on page 36), you

can apply washing-up liquid or

Vaseline to the seals (item 3 in

Fig. 34) on the air spigots.

11.4

Removing the electronics

compartment cover plate

►

Use the screwdriver to loosen the

Torx screw (item 1 in Fig. 35) on the

electronics compartment cover plate

(item 2 in Fig. 35).

►

Remove the electronics compartment

cover plate.

11.5

Threading in cables through the

opening

►

Hold the ventilation unit in front of the

installation location.

►

Thread the mains cable into the

opening (item 1 in Fig. 36) on the

ventilation unit and pull the cable

through the opening.

►

Thread the control cable (if used) into

the opening (item 1 in Fig. 36) on

the ventilation unit and pull the cable

through the opening.

►

Thread the control cable for the

M-WRG-II O/EGG-AUS option (if

used) into the opening (item 1 in

Fig. 36) on the ventilation unit and

pull the cable through the opening.

Fig. 34:

Checking the air flap on the exhaust air spigot

and seals

Fig. 35: Removing the electronics compartment cover

plate

Fig. 36: Threading in the mains cable and control cable

(if used)

Содержание M-WRG-II

















































Результаты поиска

Содержание M-WRG-II

Отзывы:

Похожие инструкции для M-WRG-II

Бренды по названию

Популярные бренды

Meltem M-WRG-II, Руководство по установке

Результаты поиска

Содержание M-WRG-II

Отзывы:

Похожие инструкции для M-WRG-II

Бренды по названию

Популярные бренды