28
29
Positioning the appliance
• Always place the appliance on a dry, level, firm and
heat-resistant surface well away from any edges.
• The back of the appliance must be supported by a
rear wall.
Connection
1. The appliance must be connected to a 230-volt AC
current, 50 Hz.
2. Always use new hoses when installing the
appliance. Old hoses should not be reused for new
installations.
3.
º
The water intake on the appliance ends in a ¾”
female plug – check that the correct hose is
used.
º
Do not overtighten the connection, as this can
damage the thread.
º
There should be a stopcock connected to the
hose, so it is easy to disconnect the water supply
to the appliance.
º
Regulations stipulate that the water tap
connection should be with a non-return valve.
However, we recommend that the appliance has
a permanent connection to the water supply. You
must ensure that the correct spacers or adapters
are used to connect the appliance in a safe and
responsible way.
º
The appliance can be connected to both hot and
cold water supply.
• If the hot water supply temperature cannot
be maintained under 60 ºC, the appliance
must be connected to the cold water supply,
as it may be damaged by water that is too
hot.
• When connected to hot water, wash times
are reduced by approximately 15 minutes.
There will also be a slight reduction in wash
efficiency.
º
The appliance is equipped with a water level
gauge, which ensures that the appliance stops
automatically if there is a drop in water pressure.
4.
until the hose is secure.
º
The drainage hose is fed upwards like an
upturned U over the accompanying plastic
the drain. This prevents drainage water flowing
back into the appliance. For increased
protection, a reflux valve (not included) can be
used.
º
The drainage hose should be fed down into
a drainage pipe, which must be no higher than
max. 75 cm above the base of the appliance.
The drainage pipe diameter should be at least
4 cm in order to ensure that air can escape
around the drainage hose. Extra drainage hose (if
any): max. length 4 m.
5. Turn water on.
NOTE! AS SOON AS THE WATER SUPPLY IS TURNED
ON, THERE IS PRESSURISED WATER IN THE HOSE
AND APPLIANCE, EVEN IF THE WATER SUPPLY IS
SUBSEQUENTLY TURNED OFF AGAIN!
Fitting the filter, rack and cutlery basket
• Fit the filters in the base of the appliance.
º
Fit the main filter (9) first. Then insert the fine
and coarse filter element (8). Then turn the filter
clockwise.
º
Check that the filters are correctly fitted and that
the dishwasher arm (7) rotates freely and can
turn a complete circle.
• The rack (1) is equipped with wheels, so that it
slides easily in and out.
• Position the cutlery basket (2) on the rack. The
cutlery basket can be removed from the rack if it
is not required, e.g. when washing serving dishes,
bowls and other large objects.
Filling salt
Water hardness varies from place to place and from
waterworks to waterworks. Hard water can leave
white deposits on dishes and requires more detergent.
This appliance is therefore equipped with a softener,
which softens the water in the appliance with the aid
of salt, which helps to ensure good washing results.
Soft water requires less detergent, so the salt helps to
reduce detergent consumption and also protect the
environment.
To fill with salt:
• Remove the cutlery basket and screw off the salt
compartment cap (6).
• Fit the funnel (10) into the port. Fill with about 1 kg
salt.
• Close cap.
• IMPORTANT! Immediately after filling with salt, run a
quick wash program to avoid salt water corrosion of
the parts.
• Refill with salt when the salt indicator (c) lights up.
NOTE! IT IS IMPORTANT TO ADD SALT BEFORE THE
FIRST WASH CYCLE! ONLY USE SALT INTENDED FOR
DISHWASHERS.
Filling dishwasher rinse agent
The surface-active substances in dishwasher rinse
agent reduce surface tension in the water for quicker,
better drying. Using a dishwasher rinse agent also
means dishes are cleaner and glass remains clear and
shiny.
To fill with dishwasher rinse agent:
• Screw the cap off the dishwasher rinse agent
compartment (3), turning it to the left (in the
direction of the arrow). Lift cap off.
• Fill dishwasher rinse agent but be careful not to
overfill the compartment.
• Screw the cap back on, turning it to the right (in the
direction of the arrow) to close.
• Refill when the dishwasher rinse indicator (d) lights
up.
Screw the hose to the water supply (
16
) at the water
intake (
15
).
14
Attach the drainage hose ( ) to the drainage nozzle
( ) using the hose clip (
17
). Tighten the hose clip
13
U-bend ( ) before being fed downwards into
12
Содержание 1659-0008
Страница 44: ...44...