Megger BERT-20E1 Скачать руководство пользователя страница 20

Страница: 20 / 24

CRC4 Level -

915 or more CRC4 code words out of 1000 received
in error

CAS Level -

Two consecutive MF alignment words received in
error

Alarm Indication Signal (AIS):

Unframed ALL ONES, more than (2) zero’s in (2)
frames (512 bits)

FAS Remote Alarm (RRA):

Bit 3 of non-align frame set to zero for (3)
consecutive occasions

MAS Remote Alarm (RDMA):

Bit 6 in time slot 16 set to zero for (2) consecutive
multiframes

Timeslot Data Drop:

Selected time slot to 8 data-bit LEDs and speaker

Signaling Types:

CCS and CAS

Digit Capture:

DTMF

CAS Signaling Bits:

A, B, C, D to (4) discrete LEDs

EXT CLOCK IN

Input Impedance:

Ω

±5%

Range:

0 to –43 dB

Compatibility:

ITU-T G.703, G.704, G.706, G.823, G.732, and I.431

ETS 300 011, 300 233, and 300 166 CTR12 and
CTR4.

Transmitter

Line Code:

AMI or HDB3

Framing:

NONE, PCM30, PCM30C, PCM31 and PCM31C

Frequency:

2048000 Hz ± 2.5 ppm

Line Coding:

AMI, HDB3

Test Patterns:

PRBS: 2

-1, 2

-1

Word:

Two user defined 64-bit word, all ONES, all

ZEROS, 1:1

Status/History:

■

TEST SUMMARY

■

AMI

■

HDB3

■

FAS SYNC

■

OCTET SYNC

■

MAS SYNC

■

PATTERN SYNC

■

SIGNAL PRESENT

■

OUT OF FRAME

■

PATTERN SYNC LOSS

■

AIS

■

FAS REMOTE ALARM

■

MAS REMOTE ALARM

■

CRC-4 DETECT

Pattern Sync Loss:

100 bit errors in 1000 bits

Pattern Sync Gain:

0 bit errors in N + 1200 bits, N = 20 for 2^15-1, N =
pattern length for the other pattern

Signal Present:

Absent when 255 consecutive zeros (no pulses)
have been detected

Out of Frame:

FAS level - (3) consecutive incorrect FAS frames
received

BERT_20E1_6172-871_UG_V02 05/05/2004 8:24 am Page 20

Содержание BERT-20E1

























Результаты поиска

Содержание BERT-20E1

Отзывы:

Бренды по названию

Популярные бренды

Megger BERT-20E1, Руководство пользователя

Результаты поиска

Содержание BERT-20E1

Отзывы:

Бренды по названию

Популярные бренды