background image

Installation & User Manual

3

Warnings

Contact Medifab 

Email: [email protected] 

New Zealand Head Office:  

 

Australian Head Office:

7-9 Allens Road 

 

 

 

26 Pardoe Street

Ashburton 7700   

 

 

East Devonport, TAS 7310

Phone  

+64 3 307 9790   

 

Phone   +61 3 6427 0105

Fax  

+64 3 307 2820   

 

Fax  

+61 3 6427 0107

Remember, your child’s safety is your responsibility. Please read this instruction 

manual completely before using this product.  Failure to follow these instructions 

and warnings could result in serious injury or death.  Keep these instructions for 

future reference.

• 

Prevent serious injury or death from falls or sliding out.

• 

Always secure user with the appropriate restraints. Snugly adjust the 

restraint belts to fit your child.

• 

Never leave the user unattended.

• 

Never adjust seating when user is sitting in seat.

• 

Do not allow user to climb into the Neat Zeat unassisted.

• 

The tray is not designed to hold the child in the Neat Zeat.

• 

Maximum weight is 75 kgs (165 lb).

• 

Avoid injuries to adults and older children from falls.  

• 

Do not use Neat Zeat as a step stool or ladder to climb up or reach 

elevated surfaces. 

• 

Do not allow adults to sit in Neat Zeat.

• 

Never use Neat Zeat without seat back attached.

• 

Do not over-tighten screws. Check and tighten the screws frequently.

• 

Check Neat Zeat for damaged hardware, loose joints, missing parts 

or sharp edges before and after assembly and frequently during use. 

Do not use Neat Zeat unless all components are correctly fitted and 

adjusted. Do not use Neat Zeat if any parts are missing, damaged or 

broken. 

• 

Do not place your Neat Zeat anywhere near hazards such as open fires 

or other significant sources of heat such as radiators, barbecues, stoves, 

etc.

• 

Do not place your child near hazards such as medication, small items 

that may pose a choking risk, trailing chords or electrical leads, etc.

• 

Only use on a flat, stable surface.

• 

Never use near stairs.

• 

Do not force the tray into child when adjusting the tray; always allow 

sufficient breathing space for your child’s comfort.

• 

Do not allow user to stand up in the Neat Zeat.

• 

Do not move the Neat Zeat with user seated unless the mobile base is 

installed.

Содержание Neat Zeat

















Отзывы: