Mecmesin MultiTest 1 Скачать руководство пользователя страница 7

Страница: 7 / 12

page 5

MULTITEST 1 SPECIFICATIONS

Load capacity

1000N/100kgf/220lbf

Power consumption

60 watts (maximum)

Weight (stand only)

20kg (44lb)

CROSSHEAD MOTION

Travel range

500mm (19.68in)

Maximum daylight

630mm (24.80in)

Maximum headroom

510mm (20.08in)

Speed range

2.5 - 1000mm/min

Up and down settings

by toggle switch

Stand speed indicated

by potentiometer/graduated dial

Direction of travel indicated

LED

Limit switch repeatability

< 0.5mm (0.020in)

Over-run at top speed

< 2mm (0.08in)

Operating modes

Manual & single cycle with fast return

Reverse on alarm point

Yes, with AFG or AFTI cable

Reverse on sample break

Yes, with AFG or AFTI cable

ENVIRONMENTAL OPERATING CONDITIONS

Temperature range

C to 40

Humidity

< 92.5%

STANDARD LOAD MEASUREMENT OPTIONS

Force Gauge and dovetail bracket

Yes

Anvil plate

Yes

S-beam Loadcell, tension
block module & AFTI

Yes

SPECIAL OPTIONS

Increased crosshead travel

Increased crosshead depth

Yes, reduced load capacity

Machine guard

Yes

Horizontal operation

Yes

Simple logging/plotting PC software

DataPlot (see document M/501201)

Full computer control

MultiTest 1-

Internal storage of test programs

MultiTest 1-

Содержание MultiTest 1













Результаты поиска

Содержание MultiTest 1

Отзывы:

Похожие инструкции для MultiTest 1

Бренды по названию

Популярные бренды

Mecmesin MultiTest 1, Руководство по эксплуатации

Результаты поиска

Содержание MultiTest 1

Отзывы:

Похожие инструкции для MultiTest 1

Бренды по названию

Популярные бренды