mecalac TA3.5SH Скачать руководство пользователя страница 71

Страница: 71 / 136

TA3H, TA3SH & TA3.5SH

Page 7 - 9

7. Standard Operating Procedures

(6)

To Lower the Skip

(7)

To Return the Skip to the Ahead (Travelling) Position

7.10

Parking the Machine After Use

At the end of the working day make sure the machine is parked safely and securely

PROCEDURE

When the load has been discharged.

Move the control lever towards the back of the machine.

The skip will lower.

PROCEDURE

If necessary raise the skip to clear the lock.

Rotate the skip to the ahead position.

.Move the control lever towards the back of the machine; the skip will lower.

Make sure the skip is locked in the ahead position.

PROCEDURE

Find a safe, flat, well lit area to park the machine where it will not cause an obstruction or
danger to others.

Set the forward/reverse switch to the Neutral position and apply the parking brake.

Stop the engine and remove the start key.

Lift the engine cover, turn the battery isolator to OFF and remove the isolator key.

Close the engine cover, lock and remove the key.

Содержание TA3.5SH









































































































































Результаты поиска

Содержание TA3.5SH

Отзывы:

Бренды по названию

Популярные бренды

mecalac TA3.5SH, Оригинальное руководство пользователя

Результаты поиска

Содержание TA3.5SH

Отзывы:

Бренды по названию

Популярные бренды