mecalac TA3.5SH Скачать руководство пользователя страница 68

Страница: 68 / 136

Page 7 - 6

TA3H, TA3SH & TA3.5SH

7. Standard Operating Procedures

7.6

To Stop the Engine

7.7

To Move the Machine

Refer to Figure 7.7

Figure 7.7. - Forward/Reverse and Fast Slow Switches

Forward Reverse Switch - A, Forward - B, Neutral - C, Reverse

Speed Switch - D, Fast - E, Slow

7.8

Loading the Skip

Before the skip is loaded the operator should:-

• Park the machine safely.

• Apply parking brake and stop engine.

• Get off the machine and stand clear.

PROCEDURE

Stop the machine in a safe position on firm level ground.

Apply parking brake and place the forward/reverse switch in Neutral.

Turn start key anticlockwise to OFF - position 0.

PROCEDURE

Make sure the parking brake is ON.

Make sure the forward/reverse switch in Neutral.

Start the engine.

Select Fast or Slow on the speed switch.

Select Forward or Reverse.

Release the parking brake.

Depress the accelerator pedal gently and the machine will begin to move.

Control the speed of the machine with the accelerator or brakes as required.

COV00226

Содержание TA3.5SH









































































































































Результаты поиска

Содержание TA3.5SH

Отзывы:

Бренды по названию

Популярные бренды

mecalac TA3.5SH, Оригинальное руководство пользователя

Результаты поиска

Содержание TA3.5SH

Отзывы:

Бренды по названию

Популярные бренды