manualshive.com logo in svg

mecalac TA3.5SH, Оригинальное руководство пользователя

Поделиться
Скачать
mecalac TA3.5SH Скачать руководство пользователя страница 21

Page 2 - 8

TA3H, TA3SH & TA3.5SH

2. Safety

2.12

Water Cooled Engines

Water cooled systems operate under pressure to increase the boiling point of the coolant.
Therefore, the coolant temperature may be greater than boiling water at standard atmospheric
pressure (100ºC).

Never Maintain Cooling System when the Engine is HOT.

2.13

Lubricants

Lubricants should be handled in accordance to the lubrication manufacturers recommended
practices.

Whenever handling oil products, maintain good standards of care plus personal and plant
hygiene.

For details of these precautions we advise you to read the relevant publications issued by your
local health authority.

• Avoid contact with lubricants. Wear oil resistant gloves when performing maintenance.

• ALWAYS keep lubricants out of reach of children.

• NEVER store lubricants in open or unlabelled containers.

(a)

New Oil

There are no special precautions needed for the handling or use of new oil other than the normal
care and hygiene practices.

(b)

Old Oil

Used engine crankcase lubricants contain harmful contaminants. In laboratory tests it was shown
used engine oils can cause skin cancer and reproductive harm. Avoid inhalation of vapours,
ingestion and prolonged skin contact with used engine oils. Dispose of used oil in accordance
with local environmental regulations.

Observe the following precautions.

• Avoid prolonged, excessive or repeated skin contact with used engine oil.

• Apply a barrier cream to the skin before handling used engine oil.

• Note the following when removing engine oil from the skin.

• Wash skin thoroughly with soap and water. Using a nail brush will help.

• Use special hand cleansers to help clean dirty hands.

• Never use petrol, diesel fuel or kerosene.

• Avoid skin contact with oil soaked clothing.

• Do not keep oily rags in pockets.

• Wash dirty clothing before reuse.

• Throw away oil soaked shoes.

(C)

First Aid - Oil

(1)

Swallowing Oil

If oil is swallowed, do not induce vomiting.

Get Medical Advice.

(2)

Skin Contact

In the case of excessive skin contact, wash with soap and water.

(3)

Eye Contact

In the case of eye contact, flush with water for 15 minutes. If the irritation persists, get medical
attention.

2.14

Oil or Fuel Spillage

Absorb with sand or a locally approved brand of absorbent granules. Scrape up and dispose of
in a chemical disposal area.

Содержание TA3.5SH









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды