Mec 3072RT Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 100

background image

March 2008

"3072RT / 3772RT / 3772RT HD" Service & Parts Manual - ANSI Specifications

Page 4-12

PROPORTIONAL SPEED ADJUSTMENT

Proportional Circuit Board Adjustment should only be performed after all other
components are deemed to be in proper working order.

There are many factors that may contribute to excessively fast or slow drive speeds. Proportional
Circuit Board Adjustment should only be performed after all other components are deemed to be
in proper working order and not contributing to abnormal driving speeds. Failure to do so may
result in incorrect speeds once the offending component has been repaired.

Circuit Board Setting Test Procedure

Before you begin, ensure there are no overhead obstructions preventing lift to full height. Lay out
a course measured at 20 feet (6 meters) long. Ensure there are no obstructions preventing a
straight travel over the distance of the course including leading up to and away from the course.
Try not to steer while driving the timed course.

High Speed Drive Test:

With the platform fully lowered, drive the machine over the course, crossing the start line at full
speed. Record the time it takes for a (predetermined) point on the machine to cross both lines
and compare with the chart below using the ‘High Range’ column figure.

Elevated Speed Drive Test:

Elevate the platform above 12 feet (3.6 meters). Drive the machine over the course, crossing the
start line at full speed. Record the time it takes for a (predetermined) point on the machine to
cross both lines and compare with the chart below using the ‘Low Range’ column figure.

20 FT (6m)

RUN-IN

RUN-OUT

TRIM POT

High Range

Low Range

TRAVEL TIME

IN SECONDS

3.5 to 4.0

27 to 33

Speed Adjustment Table: 20 ft. (6 m) Course

«
...
80
81
82
83
84
...
»

Содержание 3072RT





































































































Отзывы:

Нет отзывов

Похожие инструкции для 3072RT

Бренд: Terex Страницы: 217

Бренд: Terex Страницы: 249

Бренд: Ravaglioli Страницы: 84

HA26 RTJ PRO SW

Бренд: Haulotte Страницы: 442

Бренд: JLG Страницы: 52

Бренд: JLG Страницы: 56

Бренд: JLG Страницы: 83

Бренд: JLG Страницы: 80

Бренд: JLG Страницы: 104

Бренд: JLG Страницы: 173

Бренд: Sinoboom Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды