Mec 3072RT Скачать руководство пользователя страница 49

Страница: 49 / 100

"3072RT / 3772RT / 3772RT HD" Service & Parts Manual - ANSI Specifications

March 2008

Page 2-9

Tilt

Control
Mod

Power
Mod

Upper
Control

trigger

Rel

y (option)

trigger Mod

le (option)

Throttle Rel

Throttle

olenoid

Glow Pl

g Rel

y (Die

el only)

Tor

peed Rel

Power Rel

ter

connect

witch

Relays

There are relays located inside the
control module and inside the Upper
Controls. (Refer to the Section 5 for relay
functions and interconnect).

Upper Control Power Relay

Purpose: Cuts power to Upper Controls
when Lower Controls are selected.

Torque/Speed Relay

Purpose: Disperses power to Torque
Solenoid Valve when high speed or low
speed is selected.

Outrigger Relay (option)

Purpose: Cuts power to Lift circuits until
Outriggers are fully deployed and in firm
contact with the ground.

Throttle Relay

Purpose: The electric throttle solenoid
receives its power through the Throttle
Relay.

Glow Plug Relay

Purpose: The diesel engine glow plug
receives its power through the Glow Plug
Relay.

Содержание 3072RT





































































































Результаты поиска

Содержание 3072RT

Отзывы:

Похожие инструкции для 3072RT

Бренды по названию

Популярные бренды

Mec 3072RT, Руководство по обслуживанию

Результаты поиска

Содержание 3072RT

Отзывы:

Похожие инструкции для 3072RT

Бренды по названию

Популярные бренды