Mec 3072RT Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 100

background image

March 2008

"3072RT / 3772RT / 3772RT HD" Service & Parts Manual - ANSI Specifications

Page 2-8

Tilt Alarm

The tilt sensor is located in the Control Module.

Tilt Alarm Audible

An audible warning is activated once machine is in the
raised position and reaches an unsafe angle; all functions
are disabled in this condition except Platform Lower.

Tilt Alarm Test

This can be tested by manually tipping the sensor. This
“Push-To-Test” feature enables tilt alarm to be tested
without losing its adjustment. Individually push down on
each of the three fastened corners of the tilt alarm. There
should be enough travel to cause the alarm to sound as
each corner is pressed. (There is approximately a three second delay). If the alarm does not
sound, the flange nuts have been tightened too far. Loosen the nut on the 90° corners and repeat
this test procedure.

Tilt Alarm Sensor Adjustment

• Before attempting to adjust the alarm, park the machine on a firm, flat, level surface. Use

of an inclinometer is recommended to ensure front and rear of base is level.

• Adjust the three flange nuts until the bubble on top of the sensor is centered.

• Check that the electrical connections are correct and secured tight.

Master Disconnect Switch

Battery disconnect is provided in the Control Module to facilitate servicing and also to prevent
unauthorized use of vehicle by using a padlock (to provide security).

Movement Alarm - Light (optional)

This light is activated as soon as the platform control console joystick (controller) lever is moved
off the center “Neutral” position.

THE MOVEMENT ALARM IS PROVIDED FOR YOUR PROTECTION,
AND PROTECTION OF PERSONS WORKING IN THE IMMEDIATE
AREA. DISABLING THIS IMPORTANT SAFETY DEVICE MAY RESULT
IN SERIOUS INJURY OR DEATH.

Fl

a

nge n

u

t

Tilt B

as

e

Fl

a

nge N

u

t

Level B

ubb

le

Mo

u

nting Pl

a

te

«
...
46
47
48
49
50
...
»

Содержание 3072RT





































































































Отзывы:

Нет отзывов

Похожие инструкции для 3072RT

Бренд: EASTMAN Страницы: 34

Бренд: Terex Страницы: 197

Бренд: Presto Страницы: 32

Бренд: Aichi Страницы: 23

Бренд: Aichi Страницы: 78

Бренд: JLG Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды